Earlier versions of the PDC driver registered for both
transmit and receive interrupts. The hard IRQ handler had to
communicate to the soft handler which interrupt(s) had occurred.
The PDC driver no longer registers for tx interrupts. So there is
no reason to save the intstatus. So remove the intstatus member
of the PDC state.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Three changes to improve performance in the PDC driver:
- disable and reenable interrupts while the interrupt handler is
running
- update rxin and txin descriptor indexes more efficiently
- group receive descriptor context into a structure and keep
context in a single array rather than five to improve locality
of reference
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In PDC driver, it is not necessary to use iowrite32()
when writing DMA descriptors to the transmit and receive rings.
The ring memory is in host memory. So convert to normal
assignment statements.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Previously used threaded IRQs in the PDC driver to defer
processing the rx DMA ring after getting an rx done interrupt.
Instead, use a tasklet at normal priority for deferred processing.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Remove the unnecessary rmb() from the receive path.
If the rx ring has multiple messages ready, avoid reading
last_rx_curr multiple times from the register.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The PDC driver is a mailbox controller. A mailbox controller
can report that a mailbox message has been "transmitted" either when
a tx interrupt fires or by having the mailbox framework poll. This
commit converts the PDC driver to the poll method. We found that the
tx interrupt happens when the descriptors are read by the SPU hw. Thus,
the interrupt method does not allow more than one tx message in the PDC
tx DMA ring at a time. To keep the SPU hw busy, we would like to keep
the tx ring full under heavy load.
With the poll method, the PDC driver responds that the previous message
has been transmitted if the tx ring has space for another message.
SPU request messages take a variable number of descriptors. If 15
descriptors are available, there is a good chance another message will
fit. Also increased the ring size from 128 to 512 descriptors.
With this change, I found the PDC driver hangs on its spinlock under
heavy load. The PDC spinlock is not required; so I removed it. Calls
to pdc_send_data() are already synchronized because of the channel
spinlock in the mailbox framework. Other references to ring indexes
should not require locking because they only written on either the
tx or rx side.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Minor fix to ensure that debugfs stats pseudo-files are
removed when driver module is unloaded. Previously, the call to
debugfs_remove_recursive() was never being called since the
directory was not empty, and a seg fault would occur if another
process tried to access these leftover files.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Ensure that DMA is disabled, and pointers reset, when changing
DMA base addresses in pdc_ring_init(). This allows a mailbox client
to be re-inserted after being removed. Otherwise, the DMA doesn't
restart so the client hangs while being reinserted.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
When creating the debugfs files for the PDC driver, use
octal file permissions rather than symbolic file permissions.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mailbox/mailbox-sti.ko | grep alias
alias: platform:mailbox-sti
After this patch:
$ modinfo drivers/mailbox/mailbox-sti.ko | grep alias
alias: platform:mailbox-sti
alias: of:N*T*Cst,stih407-mailboxC*
alias: of:N*T*Cst,stih407-mailbox
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mailbox/mailbox-test.ko | grep alias
$
After this patch:
$ modinfo drivers/mailbox/mailbox-test.ko | grep alias
alias: of:N*T*Cmailbox-testC*
alias: of:N*T*Cmailbox-test
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
We have to use the _safe version of list_for_each() because we're
freeing the pointer as we go along. (This might not show up testing
depending on what config options you have enabled).
Fixes: 0fe88461a0 ("mailbox: Add Tegra HSP driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This driver exposes a mailbox interface for interprocessor communication
using the Hardware Synchronization Primitives (HSP) module's doorbell
mechanism. There are multiple HSP instances and they provide additional
features such as shared mailboxes, shared and arbitrated semaphores.
A driver for a remote processor can use the mailbox client provided by
the HSP driver and build an IPC protocol on top of this synchronization
mechanism.
Based on work by Joseph Lo <josephl@nvidia.com>.
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
* acpi-x86:
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
* acpi-cppc:
ACPI / CPPC: Support PCC with interrupt flag
ACPI / CPPC: Add prefix cppc to cpudata structure name
ACPI / CPPC: Add support for functional fixed hardware address
ACPI / CPPC: Don't return on CPPC probe failure
ACPI / CPPC: Allow build with ACPI_CPU_FREQ_PSS config
ACPI / CPPC: check for error bit in PCC status field
ACPI / CPPC: move all PCC related information into pcc_data
ACPI / CPPC: add sysfs support to compute delivered performance
ACPI / CPPC: set a non-zero value for transition_latency
ACPI / CPPC: support for batching CPPC requests
ACPI / CPPC: acquire pcc_lock only while accessing PCC subspace
ACPI / CPPC: restructure read/writes for efficient sys mapped reg ops
mailbox: pcc: Support HW-Reduced Communication Subspace type 2
* acpi-soc:
ACPI / APD: constify local structures
ACPI / APD: Add device HID for Vulcan SPI controller
Add Message-Handling-Unit driver for platform variants as mailbox controller.
Actually, only the Amlogic Meson GXBB SoC MHU is supported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
ACPI 6.1 has a PCC HW-Reduced Communication Subspace type 2 intended for
use on HW-Reduce ACPI Platform, which requires read-modify-write sequence
to acknowledge doorbell interrupt. This patch provides the implementation
for the Communication Subspace Type 2.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We get 2 warnings when biuld kernel with W=1:
drivers/mailbox/bcm-pdc-mailbox.c:472:6: warning: no previous prototype for 'pdc_setup_debugfs' [-Wmissing-prototypes]
drivers/mailbox/bcm-pdc-mailbox.c:488:6: warning: no previous prototype for 'pdc_free_debugfs' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix format and type mismatches in a couple debug prints in the
Broadcom PDC driver. Use %pad for dma_addr_t and %pa for
resource_size_t.
Signed-off-by: Rob Rice <rob.rice@broadcom.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Rob Rice
Steve Lin
Javier Martinez Canillas
Linus Torvalds
Dan Carpenter
Thierry Reding
Hoan Tran
Rafael J. Wysocki
Neil Armstrong
Baoyou Xie
Rob Rice