Get rid of a silent failure mode when the MMC/SD host doesn't
support the voltages needed to operate a given card, by
adding a warning. A 3.3V host and a 3.0V card, for example,
no longer need to mysteriously just not work at all.
This isn't the best diagnostic; ideally it would also tell
what voltage the card and host support (and not just by
dumping the bitmasks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The support is implemented via platform data accessors, new module
(of_mmc_spi) will be created automatically when the driver compiles
on OpenFirmware platforms. Link-time dependency will load the module
automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
dma_unmap_sg should be given the same length as dma_map_sg, not the
value returned from dma_map_sg
Signed-off-by: Vernon Sauder <vsauder@inhand.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If a card encounters an ECC error while reading a sector it will
timeout. Instead of reporting the entire I/O request as having
an error, redo the I/O one sector at a time so that all readable
sectors are provided to the upper layers.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As reported by Randy Dunlap, having sdhci built-in and LEDs class
as a module resulted in undefined symbols. Change the code to handle
that case properly (by not having LEDs class support in sdhci).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The latest generation of laptops are shipping with a newer
model of Ricoh chip where the firewire controller is the
primary PCI function but a cardbus controller is also present.
The existing code assumes that if a cardbus controller is,
present, then it must be the one to manipulate - but the real
rule is that you manipulate PCI function 0. This patch adds an
additional constraint that the target must be function 0.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use the new pci_ioremap_bar() function in drivers/mmc.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This removes clkrt and cmdat from struct imxmci_host, they are
unused.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This cleans up the warnings issued by the checkpatch script
and remove the file history from the header
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.
The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.
Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Ricoh SD card readers seems to advertise themselves slightly differently.
This patches the driver to will recognise an additional product id, and it
appears to work perfectly.
% pccardctl info
PRODID_1="RICOH"
PRODID_2="Bay Controller"
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
Signed-off-by: Charles Lowe <aquasync@gmail.com>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As said in function comment mmc_add_host() requires that:
"The host must be prepared to start servicing requests
before this function completes."
During this function, at91_mci_request() can be invoqued
without timer beeing setup leading to a kernel Oops.
This has been reported inserting this driver as a module.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Wu Xuan <wux@landicorp.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pierre Ossman
David Brownell
Anton Vorontsov
Vernon Sauder
Adrian Hunter
Julia Lawall
Roel Kluin
philipl@overt.org
Jarkko Lavinen
Éric Piel
Harvey Harrison
Arjan van de Ven
Russell King
Marc Kleine-Budde
Tony Lindgren
Sascha Sommer
Nicolas Ferre