The new hardware design applied for this cards.
Silicon Labs C8051F300 microcontroller is used for LNB power control.
It connected to cx23885 GPIO pins:
GPIO0 - P0.3 data
GPIO1 - P0.2 reset
GPIO2 - P0.1 clk
GPIO3 - P0.0 busy
Tevii S470 based on Montage Technology M88TS2020 digital satellite tuner
and M88DS3000 advanced DVB-S/S2 demodulator.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix this trivial compile warning:
v4l/atbm8830.c:164: warning: 'set_agc_config' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18 av core implemented an init call for no good reason. It's now
turned into an internal function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a struct v4l2_device to the go7007 device struct and registers
it during v4l2 initialization. The v4l2_device registration overwrites
the go->dev device_data, which is a struct usb_interface with intfdata set
to the struct go7007. This changes intfdata to point to the struct
v4l2_device inside struct go7007, which is what v4l2_device_register will
also set it to (and warn about non-null drvdata on register.) Since usb
disconnect can happen any time, this intfdata should always be present.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid legacy IR I2C probing for PVR-150, PVR-500, and PVR-350 cards. This
still probes, but restricts the possbile addresses probed per card.
Also removed legacy probe addresses for the KNC and PixelView cards which are
not supported by ivtv as far as I know.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change creates per cx18 instances of IR_i2c_init_data for handing over
initialization data to ir-kbd-i2c, since that module wants non-const data
even though it never modifies the data.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add explicit support for the AVerTV M116 for use with the ir-kbd-i2c module.
This also eases future support for other AVerMedia ivtv boards with the same
microcontroller program at I2C address 0x40.
This is a reworked version of an earlier patch that was...
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This avoids collisions of legacy IR controller probing with known I2C devices
in the card definitions in ivtv-cards.c. I2C driver modules for device listed
explicitly in a card definition should always take precedence over a probe
guessing where and IR controller may be.
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Igor M. Liplianin
Jean-Francois Moine
Hans Verkuil
Vaibhav Hiremath
Pete Eberlein
Andy Walls