When a user application wants to set the rtc time, the RTC subsystem takes
advantage of 'rtc_valid_tm(tm)' to check 'rtc_time *tm' value validity, it
make sure the 'tm->tm_year' is larger than 70,so if '70< tm_year < 100',
the '(settm->tm_year - 100)' will be negative. ' Setting the negative
value to hardware register will be invalid, so I add the 'if' condition to
make sure set a valid value to register.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add an mdelay(1) to the polling loop to cause less frequent access to
the hardware register.
- change the return value from ENODEV to EPERM if the loop timed out. I
think the 'Operation not permitted' description is more suitable for the
meaning of 'check_rtc_access_enable()' function, it just be used to
judge rtc access operation is permitted or not.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (150 commits)
MIPS: PowerTV: Separate PowerTV USB support from non-USB code
MIPS: strip the un-needed sections of vmlinuz
MIPS: Clean up the calculation of VMLINUZ_LOAD_ADDRESS
MIPS: Clean up arch/mips/boot/compressed/decompress.c
MIPS: Clean up arch/mips/boot/compressed/ld.script
MIPS: Unify the suffix of compressed vmlinux.bin
MIPS: PowerTV: Add Gaia platform definitions.
MIPS: BCM47xx: Fix nvram_getenv return value.
MIPS: Octeon: Allow more than 3.75GB of memory with PCIe
MIPS: Clean up notify_die() usage.
MIPS: Remove unused task_struct.trap_no field.
Documentation: Mention that KProbes is supported on MIPS
SAMPLES: kprobe_example: Make it print something on MIPS.
MIPS: kprobe: Add support.
MIPS: Add instrunction format for BREAK and SYSCALL
MIPS: kprobes: Define regs_return_value()
MIPS: Ritually kill stupid printk.
MIPS: Octeon: Disallow MSI-X interrupt and fall back to MSI interrupts.
MIPS: Octeon: Support 256 MSI on PCIe
MIPS: Decode core number for R2 CPUs.
...
This patch adds HAVE_S3C_RTC to control inclusion of RTC driver for Samsung
SoCs. This option will help to include the driver only for the necessary
machines and not for any given arch.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This Patch does followings.
1) Enables support for alarm and time tick pending register
for periodic interrupt generation.
2) Changes writeb to writew beacuse the macro S3C64XX_RTCCON_TICEN
(Tick Timer Enable) is 9th bit of register.
3) Changes writeb to writel as max_user_freq used in s3c64xx is 32768 and
requires 15 bits to update the Tick Count Register.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Fix the logic while writing new date/time to the chip. The driver
incorrectly wrote back register values to different registers and even
with wrong mask. The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode. Instead of checking the hour register it reads the minute
register. Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits. This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes. The time
jump is also written back to the RTC.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>