Fixes for AT91 related to:
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller". Fix binding doc and dts
to get them match driver code.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Chris Ball <cjb@laptop.org>
From Jason Cooper <jason@lakedaemon.net>:
Small fixes for the orion platforms including kirkwood.
* 'fixes-for-v3.6' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While converting, a led has been missed leading to wrong power blue led
definition. Add it back and fix the gpio used on the power blue led.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Omap fixes for issues noted during the merge window, mostly
PM related.
* tag 'omap-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
ARM: OMAP2+: cpu: Add am33xx device under cpu_class_is_omap2
omap: Fix multi.h when only ARCH_OMAP3 and SOC_AM33XX are selected
ARM: OMAP2+: Fix dmtimer set source clock failure
Revert "ARM: OMAP3: PM: call pre/post transition per powerdomain"
ARM: OMAP3: TWL4030: ensure sys_nirq1 is mux'd and wakeup enabled
omap2: mux: remove comment for nonexistent member
OMAP: remove unused parameter arch_id from uncompress.h
arm/dts: Mark vcxio, v2v1 and v1v8 regulators as always on
OMAP2+: Fix random config build break with !ARM_CPU_SUSPEND
arm/dts: Fix am33xx wdt node
ARM: OMAP3: igep0020: set GPIO mode for mux mcspi1_cs2 pin
Revert "ARM: OMAP3530evm: set pendown_state and debounce time for ads7846"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
vcxio, v2v1 and v1v8 are expected to be always on, update the dtsi
for twl6030 to reflect this.
commit '86f5fc' regulator: core: Mark all DT based boards as having
full constraints) caused these to be disabled at late boot causing
OMAP4 boards (using twl6030) to lockup.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM i.MX fixes for 3.6-rc
* tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
i.MX27: Fix emma-prp and csi clocks.
ARM: clk-imx31: Fix the keypad clock name
ARM: dts: imx27-3ds.dts: Fix serial console node
Add am33xx wdt node.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[tony@atomide.com: I messed up and produced an empty commit db27ac80 with stg apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 88cde8b (ARM: dts: imx: update #interrupt-cells for gpio nodes)
changes gpio #interrupt-cells from 1 to 2 without updating the users.
It causes the gpio irq requesting call failing in client driver's probe
function.
Add the irq type cell for those gpio interrupt users to fix their
driver probe failure.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit c7e963f (net/smsc911x: Add regulator support), the lan9220
device tree probe fails on imx53-ard board, because the commit makes
VDD33A and VDDVARIO supplies mandatory for the driver.
Add a fixed dummy 3V3 supplying lan9220 to fix the regression.
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In order to have audio functional on mx6qsabrelite, it is necessary
to setup the IOMUX for MX6Q_PAD_GPIO_0__CCM_CLKO pins as it provides
the audio clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull EDAC patches from Mauro Carvalho Chehab:
- the second part of the EDAC rework:
- Add the sysfs nodes that exports the real memory layout, instead
of the fake one (needed to properly represent Intel memory
controllers since 2002)
- convert EDAC MC to use "struct device" instead of creating the
sysfs nodes via the kobj API
- adds a tracepoint to represent memory errors
- some cleanup patches
- some fixes at i5000, i5400 and EDAC core
- a new EDAC driver for Caldera.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (33 commits)
edac i5000, i5400: fix pointer math in i5000_get_mc_regs()
edac: allow specifying the error count with fake_inject
edac: add support for Calxeda highbank L2 cache ecc
edac: add support for Calxeda highbank memory controller
edac: create top-level debugfs directory
sb_edac: properly handle error count
i7core_edac: properly handle error count
edac: edac_mc_handle_error(): add an error_count parameter
edac: remove arch-specific parameter for the error handler
amd64_edac: Don't pass driver name as an error parameter
edac_mc: check for allocation failure in edac_mc_alloc()
edac: Increase version to 3.0.0
edac_mc: Cleanup per-dimm_info debug messages
edac: Convert debugfX to edac_dbg(X,
edac: Use more normal debugging macro style
edac: Don't add __func__ or __FILE__ for debugf[0-9] msgs
Edac: Add ABI Documentation for the new device nodes
edac: move documentation ABI to ABI/testing/sysfs-devices-edac
i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy
edac: change the mem allocation scheme to make Documentation/kobject.txt happy
...
Pull arm-soc soc updates from Olof Johansson:
"This is the second batch of SoC updates for the 3.6 merge window,
containing parts that arrived close to the merge window opening and
thus needed to sit in linux-next for a while.
Most contents is updates of Renesas shmobile, with a couple of Samsung
Exynos patches in the mix."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: S3C64XX: Add header file protection macros in pm-core.h
[CPUFREQ] EXYNOS5250: Add support max 1.7GHz for EXYNOS5250
ARM: EXYNOS: Add G2D related clock entries for SMDK4X12
ARM: EXYNOS: Move G2D clock entries to clock-exynos4210.c file
ARM: shmobile: Fix build problem in pm-sh7372.c for unusual .config
ARM: shmobile: Take cpuidle dependencies into account correctly
ARM: mach-shmobile: sh7377 generic board support via DT
ARM: mach-shmobile: r8a7740 generic board support via DT
ARM: shmobile: sh7372: completely switch over to using pm-rmobile API
ARM: shmobile: ap4evb: switch to using pm-rmobile API
ARM: shmobile: mackerel: switch to using pm-rmobile API
ARM: shmobile: sh7372: add pm-rmobile domain support
ARM: shmobile: r8a7740: add A4LC pm domain support
ARM: shmobile: r8a7740: add A3SP pm domain support
ARM: shmobile: r8a7740: add A4S pm domain support
ARM: shmobile: r8a7740: fixup: MSEL1CR 7bit control
ARM: shmobile: soc-core: add R-mobile PM domain common APIs
ARM: shmobile: sh7372 A3SM CPUIdle support
ARM: shmobile: Use INTCA with sh7372 A3SM power domain
ARM: mach-shmobile: Convert sh_clk_mstp32_register to sh_clk_mstp_register
...
Pull PWM subsystem from Thierry Reding:
"The new PWM subsystem aims at collecting all implementations of the
legacy PWM API and to eventually replace it completely.
The subsystem has been in development for over half a year now and
many drivers have already been converted. It has been in linux-next
for a couple of weeks and there have been no major issues so I think
it is ready for inclusion in your tree."
Arnd Bergmann <arnd@arndb.de>:
"Very much Ack on the new subsystem. It uses the interface
declarations as the previously separate pwm drivers, so nothing
changes for now in the drivers using it, although it enables us to
change those more easily in the future if we want to.
This work is also one of the missing pieces that are required to
eventually build ARM kernels for multiple platforms, which is
currently prohibited (amongs other things) by the fact that you cannot
have more than one driver exporting the pwm functions."
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Philip, Avinash <avinashphilip@ti.com> # TI's AM33xx platforms
Acked-By: Alexandre Pereira da Silva <aletes.xgr@gmail.com> # LPC32XX
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Fix up trivial conflicts with other cleanups and DT updates.
* 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm: (36 commits)
pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
pwm: pwm-tiecap: PWM driver support for ECAP APWM
pwm: fix used-uninitialized warning in pwm_get()
pwm: add lpc32xx PWM support
pwm_backlight: pass correct brightness to callback
pwm: Use pr_* functions in pwm-samsung.c file
pwm: Convert pwm-samsung to use devm_* APIs
pwm: Convert pwm-tegra to use devm_clk_get()
pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
pwm: pxa: Propagate pwmchip_remove() error
pwm: Convert pwm-pxa to use devm_* APIs
pwm: Convert pwm-vt8500 to use devm_* APIs
pwm: Convert pwm-imx to use devm_* APIs
pwm: Conflict with legacy PWM API
pwm: pwm-mxs: add pinctrl support
pwm: pwm-mxs: use devm_* managed functions
pwm: pwm-mxs: use global reset function stmp_reset_block
pwm: pwm-mxs: encode soc name in compatible string
pwm: Take over maintainership of the PWM subsystem
...
Olof Johansson
Arnd Bergmann
Shawn Guo
Bo Shen
Arnaud Patard (Rtp)
Linus Torvalds
Rajendra Nayak
Afzal Mohammed
Fabio Estevam
Thomas Petazzoni