In skb_checksum complete, if we need to compute the checksum for the
packet (via skb_checksum) save the result as CHECKSUM_COMPLETE.
Subsequent checksum verification can use this.
Also, added csum_complete_sw flag to distinguish between software and
hardware generated checksum complete, we should always be able to trust
the software computation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when the first checksum in a packet is validated using
CHECKSUM_COMPLETE, ip_summed is overwritten to be CHECKSUM_UNNECESSARY
so that any subsequent checksums in the packet are not correctly
validated.
This patch adds csum_valid flag in sk_buff and uses that to indicate
validated checksum instead of setting CHECKSUM_UNNECESSARY. The bit
is set accordingly in the skb_checksum_validate_* functions. The flag
is checked in skb_checksum_complete, so that validation is communicated
between checksum_init and checksum_complete sequence in TCP and UDP.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
This series contains an enhancement in the area of firmware minidump collection
and optimization of ring count validation function.
Please apply this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings:
net/ipv4/ip_tunnel.c:245:53: warning: restricted __be16 degrades to integer
net/ipv4/ip_vti.c:321:19: warning: incorrect type in assignment (different base types)
net/ipv4/ip_vti.c:321:19: expected restricted __be16 [addressable] [assigned] [usertype] i_flags
net/ipv4/ip_vti.c:321:19: got int
net/ipv4/ip_vti.c:447:24: warning: incorrect type in assignment (different base types)
net/ipv4/ip_vti.c:447:24: expected restricted __be16 [usertype] i_flags
net/ipv4/ip_vti.c:447:24: got int
Since VTI_ISVTI is always used with ip_tunnel_parm->i_flags (which is __be16),
we can __force cast VTI_ISVTI to __be16 in header file.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.
Fixes: e194312854 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse complained about this bogus extern on definition of
a function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a description of eBPFs instruction encoding in order
to bring the documentation in line with the implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the term eBPF is used anyway on mailing list discussions, lets
also document that in the main BPF documentation file and replace a
couple of occurrences with eBPF terminology to be more clear.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add lib/test_bpf.c entry to maintainers file under networking.
All changes were posted via netdev for review, so make sure
other people Cc it as well when they call get_maintainer.pl.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:ee45fd92c739
("sfc: Use TX PIO for sufficiently small packets")
The linux net driver uses memcpy_toio() in order to copy into
the PIO buffers.
Even on a 64bit machine this causes 32bit accesses to a write-
combined memory region.
There are hardware limitations that mean that only 64bit
naturally aligned accesses are safe in all cases.
Due to being write-combined memory region two 32bit accesses
may be coalesced to form a 64bit non 64bit aligned access.
Solution was to open-code the memory copy routines using pointers
and to only enable PIO for x86_64 machines.
Not tested on platforms other than x86_64 because this patch
disables the PIO feature on other platforms.
Compile-tested on x86 to ensure that works.
The WARN_ON_ONCE() code in the previous version of this patch
has been moved into the internal sfc debug driver as the
assertion was unnecessary in the upstream kernel code.
This bug fix applies to v3.13 and v3.14 stable branches.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita says:
====================
bridge: 802.1ad vlan protocol support
Currently bridge vlan filtering doesn't work fine with 802.1ad protocol.
Only if a bridge is configured without pvid, the bridge receives only
802.1ad tagged frames and no STP is used, it will work.
Otherwise:
- If pvid is configured, it can put only 802.1Q tags but cannot put 802.1ad
tags.
- If 802.1Q and 802.1ad tagged frames arrive in mixture, it applies filtering
regardless of their protocols.
- While an 802.1ad bridge should use another mac address for STP BPDU and
should forward customer's BPDU frames, it can't.
Thus, we can't properly handle frames once 802.1ad is used.
Handling 802.1ad is useful if we want to allow stacked vlans to be used,
e.g., guest VMs wants to use vlan tags and the host also wants to segregate
guest's traffic from other guests' by vlan tags.
Here is the image describing how to configure a bridge to filter VMs traffic.
+-------+p/u +-----+ +---------+
+----+ | |------|vnet0|--|User A VM|
|eth0|--|802.1ad| +-----+ +---------+
+----+ |bridge |p/u +-----+ +---------+
| |------|vnet1|--|User B VM|
+-------+ +-----+ +---------+
p/u: pvid/untagged
This patch set enables us to set vlan protocols per bridge.
This tries to implement a bridge like S-VLAN component in IEEE 802.1Q-2011
spec.
Note that there is another possible implementation that sets vlan protocols
per port. Some HW switches seem to take that approach.
However, I think per-bridge approach is better, because;
- I think the typical usage of an 802.1ad bridge is segregating 802.1Q tagged
traffic (like what is described above), and this doesn't need the ability to
be set protocols per port. Also, If a bridge has many ports and it supports
per-port setting, we might have to make much more extra configurations to
change protocols of all ports.
- I assume that the main perpose to set protocol per port is to assign S-VID
according to C-VID, or to realize two logical bridges (one is an 802.1Q
filtering bridge and the other is an 802.1ad filtering bridge) in one bridge.
The former usually needs additional features such as vlan id mapping, and
is likely to make bridge's code complicated. If a user wants, such enhanced
features can be accomplished by a combination of multiple bridges, so it is
not absolutely necessary to implement these features in a bridge itself.
The latter is simply unnecessary because we can easily make two bridges of
which one is an 802.1Q bridge and the other is an 802.1ad bridge.
Here is an example of the enhanced feature that we can realize by using
multiple bridges and veth interfaces. This way is documented in
IEEE 802.1Q-2011 clause 15.4 (C-tagged service interface).
+----+ +-------+p/u +------+ +----+ +--+
|eth0|--|802.1ad|----veth----|802.1Q|--|vnet|--|VM|
+----+ |bridge |----veth----|bridge| +----+ +--+
+-------+p/u +------+
p/u: pvid/untagged
In this configuration, we can map C-VIDs to any S-VID.
For example;
C-VID 10 and 20 to S-VID 100
C-VID 30 to S-VID 110
This is achieved through the 802.1Q bridge that forwards C-tagged frames to
proper ports of the 802.1ad bridge.
Changes:
v1 -> v2:
- Make the way to forward bridge group addresses more generic by introducing
new mask, group_fwd_mask_required.
RFC -> v1:
- Add S-TAG tx offload.
- Remove a fix around stacked vlan which has already been fixed.
- Take into account Bridge Group Addresses.
- Separate handling of protocol-mismatch from br_vlan_get_tag().
- Change the way to set vlan_proto from netlink to sysfs because no other
existing configuration per bridge can be set by netlink.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to change the vlan protocol for vlan filtering.
We come to be able to filter frames on the basis of 802.1ad vlan tags
through a bridge.
This also changes br->group_addr if it has not been set by user.
This is needed for an 802.1ad bridge.
(See IEEE 802.1Q-2011 8.13.5.)
Furthermore, this sets br->group_fwd_mask_required so that an 802.1ad
bridge can forward the Nearest Customer Bridge group addresses except
for br->group_addr, which should be passed to higher layer.
To change the vlan protocol, write a protocol in sysfs:
# echo 0x88a8 > /sys/class/net/br0/bridge/vlan_protocol
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge is an 802.1ad bridge, it must forward another bridge group
addresses (the Nearest Customer Bridge group addresses).
(For details, see IEEE 802.1Q-2011 8.6.3.)
As user might not want group_fwd_mask to be modified by enabling 802.1ad,
introduce a new mask, group_fwd_mask_required, which indicates addresses
the bridge wants to forward. This will be set by enabling 802.1ad.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables a bridge to have vlan protocol informantion and allows vlan
tag manipulation (retrieve, insert and remove tags) according to the vlan
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e9ce7cb6b1 ("xen-netback: Factor queue-specific data into
queue struct") added a use of vzalloc/vfree to interface.c, but
removed the #include <linux/vmalloc.h> statement at the same time,
which causes this build error:
drivers/net/xen-netback/interface.c: In function 'xenvif_free':
drivers/net/xen-netback/interface.c:754:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(vif->queues);
^
cc1: some warnings being treated as errors
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert
David S. Miller
Shahed Shaikh
Dmitry Popov
Dan Carpenter
Varka Bhadram
stephen hemminger
Alexei Starovoitov
Eric Dumazet
Daniel Borkmann
Octavian Purdila
Jon Cooper
Toshiaki Makita
Arnd Bergmann
Jongsung Kim
Yoshihiro Shimoda