Get rid of the duplicated rtnetlink macros and use the generic netlink
attribute functions. The old duplicated stuff is moved to a new header
file that exists just for userspace.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
rfkill_switch_all shouldn't be called by drivers directly,
instead they should send a signal over the input device.
To prevent confusion for driver developers, move the
function into a rfkill private header.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stateless NAT is useful in controlled environments where restrictions are
placed on through traffic such that we don't need connection tracking to
correctly NAT protocol-specific data.
In particular, this is of interest when the number of flows or the number
of addresses being NATed is large, or if connection tracking information
has to be replicated and where it is not practical to do so.
Previously we had stateless NAT functionality which was integrated into
the IPv4 routing subsystem. This was a great solution as long as the NAT
worked on a subnet to subnet basis such that the number of NAT rules was
relatively small. The reason is that for SNAT the routing based system
had to perform a linear scan through the rules.
If the number of rules is large then major renovations would have take
place in the routing subsystem to make this practical.
For the time being, the least intrusive way of achieving this is to use
the u32 classifier written by Alexey Kuznetsov along with the actions
infrastructure implemented by Jamal Hadi Salim.
The following patch is an attempt at this problem by creating a new nat
action that can be invoked from u32 hash tables which would allow large
number of stateless NAT rules that can be used/updated in constant time.
The actual NAT code is mostly based on the previous stateless NAT code
written by Alexey. In future we might be able to utilise the protocol
NAT code from netfilter to improve support for other protocols.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to create a new network namespace
using sys_clone, or sys_unshare.
As the network namespace is still experimental and under development
clone and unshare support is only made available when CONFIG_NET_NS is
selected at compile time.
As this patch introduces network namespace support into code paths
that exist when the CONFIG_NET is not selected there are a few
additions made to net_namespace.h to allow a few more functions
to be used when the networking stack is not compiled in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds fields to support the informational Data 1..3 fields of the
DCCP-Reset packets (RFC 4340, 5.6), and makes minor cosmetic changes
to documentation.
Code which fills in these fields follows in subsequent patches, it is
primarily used for reporting option-processing and feature-negotiation
errors.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Am Freitag, 21. September 2007 schrieb Herbert Xu:
> Please don't use LLTX in new drivers. We're trying to get rid
> of it since it's
>
> 1) unnecessary;
> 2) causes problems with AF_PACKET seeing things twice.
I suggest to document that LLTX is deprecated.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I proposed introducing a list_for_each_entry_continue_reverse macro
to be used in setup_net() when unrolling the failed ->init callback.
Here is the macro and some more cleanup in the setup_net() itself
to remove one variable from the stack :) The same thing is for the
cleanup_net() - the existing list_for_each_entry_reverse() is used.
Minor, but the code looks nicer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy
Eric W. Biederman
Ivo van Doorn
Michael Buesch
Herbert Xu
Johannes Berg
Stephen Hemminger
Gerrit Renker
Ilpo Järvinen
Christian Borntraeger
Daniel Lezcano
Al Viro
Joe Perches
Pavel Emelyanov
Andy Gospodarek
Francois Romieu