This patch adds support for IRTOUCHSYSTEMS (or UNITOP) infrared touchscreens.
The touchscreen sends data in 8-byte packets.
BYTE 0 - unknown meaning, seen only one value: 0x54
BYTE 1 - unknown meaning, 3 lowest bits indicate touch state
values seen: 0x81, 0x82 or 0x83
bit 0 = set if the screen is touched and was not touched before (touch
bit 1 = set if the screen is touched and was touched (dragging)
bit 2 = set if the touch was ended (release)
BYTES 2 and 3 - X position, high-order-byte first, range = 0 to 0x0FFF
BYTES 4 and 5 - Y position, high-order-byte first, range = 0 to 0x0FFF
BYTE 6 - unknown meaning, seen only one value: 0xFF
BYTE 7 - unknown meaning, seen only one value: 0x00
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make the driver report Y/RY up as positive value and down as negative. Also
make DPAD mapping the same as classic xpad.
Reported-by: Brian Magnuson <bdmagnuson@gmail.com>
Tested-by: Jan Kratochvil <honza@jikos.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for simulating a mouse using GPIO lines. The driver
needs an appropriate platform device to be created by architecture
code.
The driver has been tested on AT32AP7000 microprocessor using the
ATSTK1000 development board.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement getkeycode and setkeycode methods for the device so
EVIOCGKEYCODE and EVIOCSKEYCODE ioctls will work.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support to wistron_btns for leds that come with the multimedia keys.
Mail and wifi leds are supported, on laptops which have them.
Depending on the laptop, wifi subsystem may control just the led, or both
the led and the wifi card. Wifi led interface is activated only for the
former type of laptops, as the latter type is already managed. Leds are
controled by the interface in /sys/class/leds.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Reduces the polling frequency from 10 Hz to 2 Hz, which should be less a burden
for laptops wrt energy saving. As it is multimedia keys, 500ms (maximum) of
latency should be still fine for the user. In order to keep fluent the feeling
when the user is pressing several keys in a raw (such as changing the volume),
the frequency is increased for a short duration after a key is pressed.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Function keys (also called macro keys) code corrected. Using a
lastMacro variable to keep track of key currently pressed. This
ensures proper resetting when dragging the pen in the drawing
area or to another key. Also suppress sending pressure reports
when over the macro key area.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now echo "some value" > /sys/......./somefile is also acceptable.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now the old tool is remembered, and reset when a new tool is
selected via the sysfs files.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
To get an on - off reporting for proximity, absolute misc reports are
used. The mixture of absolute and relative reports is awkward
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added warnings to the points where the tablet probe may fail
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Have to use set_bit since some bit values are over 32, and bitwise or
won't work on these. To be safe for the future too, use set_bit for all
input dev capabilities
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Corrections to relative mode, was looking at wrong byte
Signed-off-by: Mark Vytlacil <mrv@wi.rr.com>
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Calculation of proximity bit and of data valid bits were reversed for
stylus reports.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Small fix that corrects the documentation on the report byte
format produced by the mouse
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When setting up input device use an array to list all the buttons
instead of setting every bit separately.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no reason to do that, just tell the compiler that
we are dealing with signed values in buffer, that's it.
Signed-off-by: Rene van Paassen <rene.vanpaassen@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ondrej Zary
Dmitry Torokhov
Adrian Bunk
Jan Kratochvil
Andi Drebes
Ping Cheng
Hans-Christian Egtvedt
Eric Piel
Rene van Paassen
Mark Vytlacil