The host1x unit found in Tegra210 SoCs is very similar to the unit in
Tegra124, but it has 2 additional channels for a total of 14 channels.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When unregistering a host1x driver, make sure to unregister the core
driver as well to prevent it from sticking around and oppose reloading
of the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
MLOCK's debug info, spewed on CDMA timeout, contains meaningless MLOCK
owner channel ID because HOST1X_SYNC_MLOCK_OWNER_CHID_F() returns shifted
value, while unshifted should be used. Fix it by changing '_F' to '_V'.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is used to read the current value of the syncpt and is
useful in situations where drivers don't schedule work and wait for the
syncpoint to increment. One particular use-case is using the syncpoint
as a VBLANK counter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the struct bus_type exported by the host1x infrastructure was
only a very basic skeleton. Turn that implementation into a more full-
fledged bus to support proper probe ordering and power management.
Note that the bus infrastructure needs to be available before any of the
drivers can be registered. This is automatically ensured if all drivers
are built as loadable modules (via symbol dependencies). If all drivers
are built-in there are no such guarantees and the link order determines
the initcall ordering. Adjust drivers/gpu/Makefile to make sure that the
host1x bus infrastructure is initialized prior to any of its users (only
drm/tegra currently).
v2: Fix building host1x and tegra-drm as modules
Reported-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of locking within host1x_device_add(), call it under the lock to
make the locking more consistent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When a driver's ->probe() function fails, the host1x bus must not call
its ->remove() function because the driver will already have cleaned up
in the error handling path in ->probe().
Signed-off-by: Thierry Reding <treding@nvidia.com>
During calibration, sets the "internal reference level for drive pull-
down" to the value specified in the Tegra TRM.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the clock lanes when calibrating the MIPI PHY on Tegra124
compatible devices.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[treding@nvidia.com: bikeshedding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
By paving the CTRL reg value, the current code changes MIPI_CAL_PRESCALE
("Auto-cal calibration step prescale") from 1us to 0.1us (val=0). In the
description for PHY's noise filter (MIPI_CAL_NOISE_FLT), the TRM states
that if the value of the prescale is 0 (or 0.1us), the filter should be
set between 2-5. However, the current code sets it to 0.
For now, let's keep the prescale and filter values as-is, which is most
likely the power-on-reset values of 0x2 and 0xa, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On 64-bit platforms an unsigned long would be 64 bit and cause
unnecessary casting when being passed to writel() or returned from
readl(). Make register values 32 bits wide to avoid that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the u32 type for the offset in the host1x_job_gather structure for
consistentcy with other structures. Negative offsets don't make sense in
this context.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reduces the amount of casting that needs to be done to get rid of
annoying warnings on 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than cast to a u32 use the struct host1x_bo pointers directly.
This avoid annoying warnings for 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding
Dmitry Osipenko
Sean Paul