The existing pcmcia platform_device structure is not used and is not needed by
the pending hx4700 PCMCIA/CF support. So let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Drive the two Bluetooth UART output GPIOs (GPIO43_BTUART_TXD, GPIO45_BTUART_RTS)
LOW during sleep mode instead of HIGH. This reduces sleep mode battery discharge
from approximately 46 mA to approximately 30 mA.
Signed-off-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
GPIO105 (nIR_ON) is requested twice: first in gpio_request_array(), then in
pxa_irda_probe(). Consequently the second request fails with EBUSY:
pxa2xx-ir: probe of pxa2xx-ir failed with error -16
This patch removes the first request, allowing pxa_irda_probe() to succeed.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
Failure is reported on hx4700 with kernel v3.3-rc1.
__mfp_validate: GPIO20 is invalid pin
__mfp_validate: GPIO21 is invalid pin
__mfp_validate: GPIO15 is invalid pin
__mfp_validate: GPIO78 is invalid pin
__mfp_validate: GPIO79 is invalid pin
__mfp_validate: GPIO80 is invalid pin
__mfp_validate: GPIO33 is invalid pin
__mfp_validate: GPIO48 is invalid pin
__mfp_validate: GPIO49 is invalid pin
__mfp_validate: GPIO50 is invalid pin
Since pxa_last_gpio is used in mfp-pxa2xx driver. But it's only
updated in pxa-gpio driver that run after mfp-pxa2xx driver.
So update the pxa_last_gpio first in mfp-pxa2xx driver.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Both reboot (via reboot(RB_AUTOBOOT)) and suspend freeze on hx4700.
Registration of pxa_gpio_syscore_ops is moved into pxa-gpio driver,
but it still exists in arch-pxa directory. It resulsts failure on
reboot and suspend.
Now remove the registration code in arch-pxa.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
This regression was introduced by the commit "ARM: pxa: add dummy
clock for sa1100-rtc", id a55b5adaf4.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
The bq24022 on these machines is a very simple regulator using gpios.
One provides the on/off functionality and a second one is used to
change the current between 100 and 500 mA.
This functionality can also be provided by the more generic gpio-regulator.
Therefore convert both machines which makes it possible to remove the
bq24022 driver later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The HP iPAQ hx4700 has 128Mb of flash provided by two Intel StrataFlash devices.
The hx4700 platform configuration defines a single 128Mb flash resource,
resulting in the MTD physmap-flash driver probing the first device only and
presuming the second device is identical:
physmap platform flash device: 08000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
physmap-flash: Found 2 x16 devices at 0x4000000 in 32-bit bank
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
erase region 2: offset=0x4000000,size=0x10000,blocks=4
erase region 3: offset=0x4040000,size=0x40000,blocks=255
physmap-flash: 2 set(s) of 2 interleaved chips --> 32 partitions of 4096 KiB
Unfortunately the two devices are not identical. The first has a device ID of
0x8816, identifying a bottom parameter device. The second has a device ID of
0x8813, identifying a top parameter device. By not probing the second device,
physmap-flash does not discover the correct block sizes.
This patch splits the configuration into two 64Mb flash resources, forcing
physmap-flash to probe both devices and thus discover the correct block sizes:
physmap platform flash device: 04000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
physmap platform flash device: 04000000 at 04000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008813
<snip>
erase region 0: offset=0x0,size=0x40000,blocks=255
erase region 1: offset=0x3fc0000,size=0x10000,blocks=4
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
Concatenating MTD devices:
(0): "physmap-flash"
(1): "physmap-flash"
into device "physmap-flash"
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
sa1100-rtc driver could be shared among sa1100/pxa/mmp series silicon.
Since clk is used in mmp series silicon, add dummy clock support in
pxa also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to hard coded irq in rtc-sa1100 driver since we could share
it among arch-sa1100/arch-pxa/arch-mmp.
We still keep hard coded register address since the requirement is
enabling both rtc-sa1100 and rtc-pxa driver. The register addresses
are conflict since they're only two wrappers on the same rtc device.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
As part of mach/irqs.h include removal from sparse, mainstone.h was missed.
This fixes the compile of the pcmcia driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-pxa/pxa25x.c and arch/arm/mach-pxa/saarb.c
included 'linux/gpio.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Arnd Bergmann
Paul Parsons
Greg Kroah-Hartman
Olof Johansson
Rob Herring
Haojian Zhuang
Haojian Zhuang
Heiko Stübner
Heikki Krogerus
Russell King
Axel Lin
Danny Kukawka