* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (53 commits)
NFS: Fix a resolution problem with nfs_inode->cache_change_attribute
NFS: Fix the resolution problem with nfs_inode_attrs_need_update()
NFS: Changes to inode->i_nlinks must set the NFS_INO_INVALID_ATTR flag
RPC/RDMA: ensure connection attempt is complete before signalling.
RPC/RDMA: correct the reconnect timer backoff
RPC/RDMA: optionally emit useful transport info upon connect/disconnect.
RPC/RDMA: reformat a debug printk to keep lines together.
RPC/RDMA: harden connection logic against missing/late rdma_cm upcalls.
RPC/RDMA: fix connect/reconnect resource leak.
RPC/RDMA: return a consistent error, when connect fails.
RPC/RDMA: adhere to protocol for unpadded client trailing write chunks.
RPC/RDMA: avoid an oops due to disconnect racing with async upcalls.
RPC/RDMA: maintain the RPC task bytes-sent statistic.
RPC/RDMA: suppress retransmit on RPC/RDMA clients.
RPC/RDMA: fix connection IRD/ORD setting
RPC/RDMA: support FRMR client memory registration.
RPC/RDMA: check selected memory registration mode at runtime.
RPC/RDMA: add data types and new FRMR memory registration enum.
RPC/RDMA: refactor the inline memory registration code.
NFS: fix nfs_parse_ip_address() corner case
...
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_intern_hash() is doing an update of a RCU guarded hash chain
without using rcu_assign_pointer() or equivalent barrier.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
Base infrastructure to enable per-module debug messages.
I've introduced CONFIG_DYNAMIC_PRINTK_DEBUG, which when enabled centralizes
control of debugging statements on a per-module basis in one /proc file,
currently, <debugfs>/dynamic_printk/modules. When, CONFIG_DYNAMIC_PRINTK_DEBUG,
is not set, debugging statements can still be enabled as before, often by
defining 'DEBUG' for the proper compilation unit. Thus, this patch set has no
affect when CONFIG_DYNAMIC_PRINTK_DEBUG is not set.
The infrastructure currently ties into all pr_debug() and dev_dbg() calls. That
is, if CONFIG_DYNAMIC_PRINTK_DEBUG is set, all pr_debug() and dev_dbg() calls
can be dynamically enabled/disabled on a per-module basis.
Future plans include extending this functionality to subsystems, that define
their own debug levels and flags.
Usage:
Dynamic debugging is controlled by the debugfs file,
<debugfs>/dynamic_printk/modules. This file contains a list of the modules that
can be enabled. The format of the file is as follows:
<module_name> <enabled=0/1>
.
.
.
<module_name> : Name of the module in which the debug call resides
<enabled=0/1> : whether the messages are enabled or not
For example:
snd_hda_intel enabled=0
fixup enabled=1
driver enabled=0
Enable a module:
$echo "set enabled=1 <module_name>" > dynamic_printk/modules
Disable a module:
$echo "set enabled=0 <module_name>" > dynamic_printk/modules
Enable all modules:
$echo "set enabled=1 all" > dynamic_printk/modules
Disable all modules:
$echo "set enabled=0 all" > dynamic_printk/modules
Finally, passing "dynamic_printk" at the command line enables
debugging for all modules. This mode can be turned off via the above
disable command.
[gkh: minor cleanups and tweaks to make the build work quietly]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use offsetof() instead of home-brewed version.
Based upon initial patch by Steven Whitehouse and suggestions
by Ben Hutchings.
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem observed:
In IPv6, in the presence of multiple routers candidates to
default gateway in one segment, each sending a different
value of preference, the Linux hosts connected to the
segment weren't selecting the right one in all the
combinations possible of LOW/MEDIUM/HIGH preference.
This patch changes two files:
include/linux/icmpv6.h
Get the "router_pref" bitfield in the right place
(as RFC4191 says), named the bit left with this fix as
"home_agent" (RFC3775 say that's his function)
net/ipv6/ndisc.c
Corrects the binary logic behind the updating of the
router preference in the flags of the routing table
Result:
With this two fixes applied, the default route used by
the system was to consistent with the rules mentioned
in RFC4191 in case of changes in the value of preference
in router advertisements
Signed-off-by: Pedro Ribeiro <pribeiro@net.ipl.pt>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I've reported, ath9k currently fails utterly when fragmentation
is enabled. This makes ath9k "support" hardware fragmentation by
not supporting fragmentation at all to avoid the double-free issue.
The patch also changes mac80211 to report errors from the driver
operation to userspace.
That hack in ath9k should be removed once the rate control algorithm
it has is fixed, and we can at that time consider removing the hw
fragmentation support entirely since it's not used by any driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_bss_info_update() can return NULL. Verify that this is not the
case before calling ieee802111_rx_bss_put() which would trigger an oops
in interrupt context in atomic_dec_and_lock().
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If something goes wrong creating the debugfs dir or when
debugfs is not compiled in, the current code might lead to
trouble; make it more robust.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no checking that the HT IEs are of the right length
which can be used by an attacker to cause an out-of-bounds
access by sending a too short HT information/capability IE.
Fix it by simply pretending those IEs didn't exist when too
short.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugfs_create_dir fails, sta_info_debugfs_add_work will not
terminate because it will find the same station again and again.
This is possible whenever debugfs fails for whatever reason; one
reason is a race condition in mac80211, unfortunately we cannot
do much about it, so just document it, it just means some station
may be missing from debugfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds
Johannes Berg
Eric Dumazet
Alexey Dobriyan
Danny ter Haar
Jason Baron
David S. Miller
Pedro Ribeiro
Trond Myklebust
Manish Katiyar
Jouni Malinen
Jiri Slaby