Reformat __reset_osd() into three distinct blocks of code
handling the three return cases.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This saves us some cycles, but does not affect the placement result at
all.
This corresponds to ceph.git commit 4abb53d4f.
Signed-off-by: Sage Weil <sage@inktank.com>
Add libceph support for a new CRUSH tunable recently added to Ceph servers.
Consider the CRUSH rule
step chooseleaf firstn 0 type <node_type>
This rule means that <n> replicas will be chosen in a manner such that
each chosen leaf's branch will contain a unique instance of <node_type>.
When an object is re-replicated after a leaf failure, if the CRUSH map uses
a chooseleaf rule the remapped replica ends up under the <node_type> bucket
that held the failed leaf. This causes uneven data distribution across the
storage cluster, to the point that when all the leaves but one fail under a
particular <node_type> bucket, that remaining leaf holds all the data from
its failed peers.
This behavior also limits the number of peers that can participate in the
re-replication of the data held by the failed leaf, which increases the
time required to re-replicate after a failure.
For a chooseleaf CRUSH rule, the tree descent has two steps: call them the
inner and outer descents.
If the tree descent down to <node_type> is the outer descent, and the descent
from <node_type> down to a leaf is the inner descent, the issue is that a
down leaf is detected on the inner descent, so only the inner descent is
retried.
In order to disperse re-replicated data as widely as possible across a
storage cluster after a failure, we want to retry the outer descent. So,
fix up crush_choose() to allow the inner descent to return immediately on
choosing a failed leaf. Wire this up as a new CRUSH tunable.
Note that after this change, for a chooseleaf rule, if the primary OSD
in a placement group has failed, choosing a replacement may result in
one of the other OSDs in the PG colliding with the new primary. This
requires that OSD's data for that PG to need moving as well. This
seems unavoidable but should be relatively rare.
This corresponds to ceph.git commit 88f218181a9e6d2292e2697fc93797d0f6d6e5dc.
Signed-off-by: Jim Schutt <jaschut@sandia.gov>
Reviewed-by: Sage Weil <sage@inktank.com>
We should not set con->state to CLOSED here; that happens in
ceph_fault() in the caller, where it first asserts that the state
is not yet CLOSED. Avoids a BUG when the features don't match.
Since the fail_protocol() has become a trivial wrapper, replace
calls to it with direct calls to reset_connection().
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
A number of assertions in the ceph messenger are implemented with
BUG_ON(), killing the system if connection's state doesn't match
what's expected. At this point our state model is (evidently) not
well understood enough for these assertions to trigger a BUG().
Convert all BUG_ON(con->state...) calls to be WARN_ON(con->state...)
so we learn about these issues without killing the machine.
We now recognize that a connection fault can occur due to a socket
closure at any time, regardless of the state of the connection. So
there is really nothing we can assert about the state of the
connection at that point so eliminate that assertion.
Reported-by: Ugis <ugis22@gmail.com>
Tested-by: Ugis <ugis22@gmail.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
When ceph_osdc_handle_map() is called to process a new osd map,
kick_requests() is called to ensure all affected requests are
updated if necessary to reflect changes in the osd map. This
happens in two cases: whenever an incremental map update is
processed; and when a full map update (or the last one if there is
more than one) gets processed.
In the former case, the kick_requests() call is followed immediately
by a call to reset_changed_osds() to ensure any connections to osds
affected by the map change are reset. But for full map updates
this isn't done.
Both cases should be doing this osd reset.
Rather than duplicating the reset_changed_osds() call, move it into
the end of kick_requests().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The kick_requests() function is called by ceph_osdc_handle_map()
when an osd map change has been indicated. Its purpose is to
re-queue any request whose target osd is different from what it
was when it was originally sent.
It is structured as two loops, one for incomplete but registered
requests, and a second for handling completed linger requests.
As a special case, in the first loop if a request marked to linger
has not yet completed, it is moved from the request list to the
linger list. This is as a quick and dirty way to have the second
loop handle sending the request along with all the other linger
requests.
Because of the way it's done now, however, this quick and dirty
solution can result in these incomplete linger requests never
getting re-sent as desired. The problem lies in the fact that
the second loop only arranges for a linger request to be sent
if it appears its target osd has changed. This is the proper
handling for *completed* linger requests (it avoids issuing
the same linger request twice to the same osd).
But although the linger requests added to the list in the first loop
may have been sent, they have not yet completed, so they need to be
re-sent regardless of whether their target osd has changed.
The first required fix is we need to avoid calling __map_request()
on any incomplete linger request. Otherwise the subsequent
__map_request() call in the second loop will find the target osd
has not changed and will therefore not re-send the request.
Second, we need to be sure that a sent but incomplete linger request
gets re-sent. If the target osd is the same with the new osd map as
it was when the request was originally sent, this won't happen.
This can be fixed through careful handling when we move these
requests from the request list to the linger list, by unregistering
the request *before* it is registered as a linger request. This
works because a side-effect of unregistering the request is to make
the request's r_osd pointer be NULL, and *that* will ensure the
second loop actually re-sends the linger request.
Processing of such a request is done at that point, so continue with
the next one once it's been moved.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In kick_requests(), we need to register the request before we
unregister the linger request. Otherwise the unregister will
reset the request's osd pointer to NULL.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The red-black node in the ceph osd request structure is initialized
in ceph_osdc_alloc_request() using rbd_init_node(). We do need to
initialize this, because in __unregister_request() we call
RB_EMPTY_NODE(), which expects the node it's checking to have
been initialized. But rb_init_node() is apparently overkill, and
may in fact be on its way out. So use RB_CLEAR_NODE() instead.
For a little more background, see this commit:
4c199a93 rbtree: empty nodes have no color"
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The red-black node node in the ceph osd event structure is not
initialized in create_osdc_create_event(). Because this node can
be the subject of a RB_EMPTY_NODE() call later on, we should ensure
the node is initialized properly for that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The red-black node node in the ceph osd structure is not initialized
in create_osd(). Because this node can be the subject of a
RB_EMPTY_NODE() call later on, we should ensure the node is
initialized properly for that. Add a call to RB_CLEAR_NODE()
initialize it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
When a connection's socket disconnects, or if there's a protocol
error of some kind on the connection, a fault is signaled and
the connection is reset (closed and reopened, basically). We
currently get an error message on the log whenever this occurs.
A ceph connection will attempt to reestablish a socket connection
repeatedly if a fault occurs. This means that these error messages
will get repeatedly added to the log, which is undesirable.
Change the error message to be a warning, so they don't get
logged by default.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
A connection's socket can close for any reason, independent of the
state of the connection (and without irrespective of the connection
mutex). As a result, the connectino can be in pretty much any state
at the time its socket is closed.
Handle those other cases at the top of con_work(). Pull this whole
block of code into a separate function to reduce the clutter.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In __unregister_linger_request(), the request is being removed
from the osd client's req_linger list only when the request
has a non-null osd pointer. It should be done whether or not
the request currently has an osd.
This is most likely a non-issue because I believe the request
will always have an osd when this function is called.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
If an osd has no requests and no linger requests, __reset_osd()
will just remove it with a call to __remove_osd(). That drops
a reference to the osd, and therefore the osd may have been free
by the time __reset_osd() returns. That function offers no
indication this may have occurred, and as a result the osd will
continue to be used even when it's no longer valid.
Change__reset_osd() so it returns an error (ENODEV) when it
deletes the osd being reset. And change __kick_osd_requests() so it
returns immediately (before referencing osd again) if __reset_osd()
returns *any* error.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In __unregister_request(), there is a call to list_del_init()
referencing a request that was the subject of a call to
ceph_osdc_put_request() on the previous line. This is not
safe, because the request structure could have been freed
by the time we reach the list_del_init().
Fix this by reversing the order of these lines.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
This would reset a connection with any OSD that had an outstanding
request that was taking more than N seconds. The idea was that if the
OSD was buggy, the client could compensate by resending the request.
In reality, this only served to hide server bugs, and we haven't
actually seen such a bug in quite a while. Moreover, the userspace
client code never did this.
More importantly, often the request is taking a long time because the
OSD is trying to recover, or overloaded, and killing the connection
and retrying would only make the situation worse by giving the OSD
more work to do.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Define and export function ceph_pg_pool_name_by_id() to supply
the name of a pg pool whose id is given. This will be used by
the next patch.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Ensure that we set the err value correctly so that we do not pass a 0
value to ERR_PTR and confuse the calling code. (In particular,
osd_client.c handle_map() will BUG(!newmap)).
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The ceph_on_in_msg_alloc() method calls the ->alloc_msg() helper which
may return NULL. It also drops con->mutex while it allocates a message,
which means that the connection state may change (e.g., get closed). If
that happens, we clean up and bail out. Avoid calling ceph_msg_put() on
a NULL return value and triggering a crash.
This was observed when an ->alloc_msg() call races with a timeout that
resends a zillion messages and resets the connection, and ->alloc_msg()
returns NULL (because the request was resent to another target).
Fixes http://tracker.newdream.net/issues/3342
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
This patch defines a single function, queue_con_delay() to call
queue_delayed_work() for a connection. It basically generalizes
what was previously queue_con() by adding the delay argument.
queue_con() is now a simple helper that passes 0 for its delay.
queue_con_delay() returns 0 if it queued work or an errno if it
did not for some reason.
If con_work() finds the BACKOFF flag set for a connection, it now
calls queue_con_delay() to handle arranging to start again after a
delay.
Note about connection reference counts: con_work() only ever gets
called as a work item function. At the time that work is scheduled,
a reference to the connection is acquired, and the corresponding
con_work() call is then responsible for dropping that reference
before it returns.
Previously, the backoff handling inside con_work() silently handed
off its reference to delayed work it scheduled. Now that
queue_con_delay() is used, a new reference is acquired for the
newly-scheduled work, and the original reference is dropped by the
con->ops->put() call at the end of the function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Both ceph_fault() and con_work() include handling for imposing a
delay before doing further processing on a faulted connection.
The latter is used only if ceph_fault() is unable to.
Instead, just let con_work() always be responsible for implementing
the delay. After setting up the delay value, set the BACKOFF flag
on the connection unconditionally and call queue_con() to ensure
con_work() will get called to handle it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
If ceph_fault() is unable to queue work after a delay, it sets the
BACKOFF connection flag so con_work() will attempt to do so.
In con_work(), when BACKOFF is set, if queue_delayed_work() doesn't
result in newly-queued work, it simply ignores this condition and
proceeds as if no backoff delay were desired. There are two
problems with this--one of which is a bug.
The first problem is simply that the intended behavior is to back
off, and if we aren't able queue the work item to run after a delay
we're not doing that.
The only reason queue_delayed_work() won't queue work is if the
provided work item is already queued. In the messenger, this
means that con_work() is already scheduled to be run again. So
if we simply set the BACKOFF flag again when this occurs, we know
the next con_work() call will again attempt to hold off activity
on the connection until after the delay.
The second problem--the bug--is a leak of a reference count. If
queue_delayed_work() returns 0 in con_work(), con->ops->put() drops
the connection reference held on entry to con_work(). However,
processing is (was) allowed to continue, and at the end of the
function a second con->ops->put() is called.
This patch fixes both problems.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
If we are creating an osd request and get an invalid layout, return
an EINVAL to the caller. We switch up the return to have an error
code instead of NULL implying -ENOMEM.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Alex Elder
Sage Weil
Jim Schutt
Yan, Zheng