Add a new "Automatic" mode to the "Broadcast RGB" range property.
When selected the driver automagically selects between full range and
limited range output.
Based on CEA-861 [1] guidelines, limited range output is selected if the
mode is a CEA mode, except 640x480. Otherwise full range output is used.
Additionally DVI monitors should most likely default to full range
always.
As per DP1.2a [2] DisplayPort should always use full range for 18bpp, and
otherwise will follow CEA-861 rules.
NOTE: The default value for the property will now be "Automatic"
so some people may be affected in case they're relying on the
current full range default.
[1] CEA-861-E - 5.1 Default Encoding Parameters
[2] VESA DisplayPort Ver.1.2a - 5.1.1.1 Video Colorimetry
v2: Use has_hdmi_sink to check if a HDMI monitor is present
v3: Add information about relevant spec chapters
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RGB color range select bit on the DP/SDVO/HDMI registers
disappeared when PCH was introduced, and instead a new PIPECONF bit
was added that performs the same function.
Add a new INTEL_MODE_LIMITED_COLOR_RANGE private mode flag, and set
it in the encoder mode_fixup if limited color range is requested.
Set the the PIPECONF bit 13 based on the flag.
Experimentation showed that simply toggling the bit while the pipe is
active doesn't work. We need to restart the pipe, which luckily already
happens.
The DP/SDVO/HDMI bit 8 is marked MBZ in the docs, so avoid setting it,
although it doesn't seem to do any harm in practice.
TODO:
- the PIPECONF bit too seems to have disappeared from HSW. Need a
volunteer to test if it's just a documentation issue or if it's really
gone. If the bit is gone and no easy replacement is found, then I suppose
we may need to use the pipe CSC unit to perform the range compression.
v2: Use mode private_flags instead of intel_encoder virtual functions
v3: Moved the intel_dp color_range handling after bpc check to help
later patches
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Note: This patch also adds a little helper intel_crtc_restore_mode for
the common case where we do a full modeset but with the same
parameters, e.g. to undo bios damage or update a property.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Added note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can de-duplicate code that's inside intel_dp_start_link_train
and intel_dp_complete_link_train.
V2: Rebase since patch 3/5 was discarded.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function doesn't use any of the registers mentioned, nor does it
return true or false. Hard to do worse. Remove it, the function is
absolutely descriptive enough to not need any comment.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Moving the DPCD just after a successful read will allow to:
- log all DPCD reads (eDP ones, changes signalled by HPD IRQ)
- don't log it if we haven't been able to read it
v2: Be sure to log the DPCD when a downstream port does not have HPD
support and the branch device asserts HPD (Jani Nikula)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Wed Dec 12 19:37:22 2012 +0000
drm/i915/hdmi: Read the HPD status before trying to read the EDID
But this time for DiplayPort.
v2: Adapt to the ibx_ name change and don't add commit hash (Chris
Wilson, Jani Nikula)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the dp and fdi code use the exact same computations (ignore minor
differences in conversion between bits and bytes).
This makes it even more apparent that we have a _massive_ mess between
cpu transcoder/fdi link/pch transcoder and pch link settings. And also
that we have hilarious amounts of confusion between edp and dp
(despite that they're identical at a link level).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This could have happened with the old crtc helper based modeset code,
but can't happen any longer with the new code.
Hence put in a WARN and adjust the comment. If no one hits this, we
can eventually remove it (like a few other such cases across our
code).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
17 ms is eerily close to 60 Hz ^-1
Unfortunately this goes back to the original DP enabling for ilk, and
unfortunately does not come with a reason for it's existance attached.
Some closer inspection of the code and DP specs shows that we set the
idle link pattern before we disable the port. And it seems like that
the DP spec (or at least our hw) only switch to the idle pattern on
the next vblank. Hence a vblank wait at this spot makes _much_ more
sense than a really long wait.
v2: Rebase fixup.
v3: Add comment requested by Paulo Zanoni saying that we don't really
know what this wait is for.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While reading docs I've noticed that this special workaround to select
the 1.6 GHz DP clock only applies to pre-production ilk machines.
Since the registers we're touching here are rather undocumented and
might be harmful on later chips, rip it out.
For the Bspec reference of this w/a look in "vol4g CPU Display
Registers [DevILK]", Section 4.1.7.1 "DP_A—DisplayPort A
Control Register", "DP_PLL_Frequency_Select".
v2: Keep a debug message as a hint in case something regresses.
Requested by Chris Wilson.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we enable the cpu edp pll in intel_dp->pre_enable and no
longer in crtc_mode_set, we can also move the modeset part to the
intel_dp->mode_set callback. Previously this was not possible because
the encoder ->mode_set callbacks are called after the crtc mode set
callback.
v2: Rebase on top of copy&pasted hsw crtc_mode_set.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Less clutter in the traces. And in both cases we yell rather loud
into the logs if we time out. Patch suggested by Chris Wilson.
v2: Annotate another I915_READ in dp_aux to be consistent - we filter
out all register io in wait_for and similar loops. Chris also
suggested to mark all dp_aux register access as _NOTRACE, but I think
we should keep all functionally relevant access around, and filter
unneeded bits in userspace after the trace is captured.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on the platforms that have a dp aux irq and also have it
enabled - vlvhsw should have one, too. But I don't have a machine to
test this on. Judging from docs there's no dp aux interrupt for gm45.
Also, I only have an ivb cpu edp machine, so the dp aux A code for
snb/ilk is untested.
For dpcd probing when nothing is connected it slashes about 5ms of cpu
time (cpu time is now negligible), which agrees with 3 * 5 400 usec
timeouts.
A previous version of this patch increases the time required to go
through the dp_detect cycle (which includes reading the edid) from
around 33 ms to around 40 ms. Experiments indicated that this is
purely due to the irq latency - the hw doesn't allow us to queue up
dp aux transactions and hence irq latency directly affects throughput.
gmbus is much better, there we have a 8 byte buffer, and we get the
irq once another 4 bytes can be queued up.
But by using the pm_qos interface to request the lowest possible cpu
wake-up latency this slowdown completely disappeared.
Since all our output detection logic is single-threaded with the
mode_config mutex right now anyway, I've decide not ot play fancy and
to just reuse the gmbus wait queue. But this would definitely prep the
way to run dp detection on different ports in parallel
v2: Add a timeout for dp aux transfers when using interrupts - the hw
_does_ prevent this with the hw-based 400 usec timeout, but if the
irq somehow doesn't arrive we're screwed. Lesson learned while
developing this ;-)
v3: While at it also convert the busy-loop to wait_for_atomic, so that
we don't run the risk of an infinite loop any more.
v4: Ensure we have the smallest possible irq latency by using the
pm_qos interface.
v5: Add a comment to the code to explain why we frob pm_qos. Suggested
by Chris Wilson.
v6: Disable dp irq for vlv, that's easier than trying to get at docs
and hw.
v7: Squash in a fix for Haswell that Paulo Zanoni tracked down - the
dp aux registers aren't at a fixed offset any more, but can be on the
PCH while the DP port is on the cpu die.
Reviewed-by: Imre Deak <imre.deak@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use drm_dp_bw_code_to_link_rate insead. It's the same thing, but
supports DP_LINK_BW_5_4 and is also used by the other drivers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And use it whenever we call code that uses the DDIs. We already have
intel_ddi.c and prefix every function with intel_ddi_something instead of
haswell_something, so I think replacing the checks with HAS_DDI makes more
sense. Just a cosmetical change, yes I know, but I have this OCD...
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Highlights of this -next round:
- ivb fdi B/C fixes
- hsw sprite/plane offset fixes from Damien
- unified dp/hdmi encoder for hsw, finally external dp support on hsw
(Paulo)
- kill-agp and some other prep work in the gtt code from Ben
- some fb handling fixes from Ville
- massive pile of patches to align hsw VGA with the spec and make it
actually work (Paulo)
- pile of workarounds from Jesse, mostly for vlv, but also some other
related platforms
- start of a dev_priv reorg, that thing grew out of bounds and chaotic
- small bits&pieces all over the place, down to better error handling for
load-detect on gen2 (Chris, Jani, Mika, Zhenyu, ...)
On top of the previous pile (just copypasta):
- tons of hsw dp prep patches form Paulo
- round scheduled work items and timers to nearest second (Chris)
- some hw workarounds (Jesse&Damien)
- vlv dp support and related fixups (Vijay et al.)
- basic haswell dp support, not yet wired up for external ports (Paulo)
- edp support (Paulo)
- tons of refactorings to prepare for the above (Paulo)
- panel rework, unifiying code between lvds and edp panels (Jani)
- panel fitter scaling modes (Jani + Yuly Novikov)
- panel power improvements, should now work without the BIOS setting it up
- extracting some dp helpers from radeon/i915 and move them to
drm_dp_helper.c
- randome pile of workarounds (Damien, Ben, ...)
- some cleanups for the register restore code for suspend/resume
- secure batchbuffer support, should enable tear-free blits on gen6+
Chris)
- random smaller fixlets and cleanups.
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (231 commits)
drm/i915: Restore physical HWS_PGA after resume
drm/i915: Report amount of usable graphics memory in MiB
drm/i915/i2c: Track users of GMBUS force-bit
drm/i915: Allocate the proper size for contexts.
drm/i915: Update load-detect failure paths for modeset-rework
drm/i915: Clear unused fields of mode for framebuffer creation
drm/i915: Always calculate 8xx WM values based on a 32-bpp framebuffer
drm/i915: Fix sparse warnings in from AGP kill code
drm/i915: Missed lock change with rps lock
drm/i915: Move the remaining gtt code
drm/i915: flush system agent TLBs on SNB
drm/i915: Kill off now unused gen6+ AGP code
drm/i915: Calculate correct stolen size for GEN7+
drm/i915: Stop using AGP layer for GEN6+
drm/i915: drop the double-OP_STOREDW usage in blt_ring_flush
drm/i915: don't rewrite the GTT on resume v4
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
drm/i915: put ring frequency and turbo setup into a work queue v5
drm/i915: don't block resume on fb console resume v2
drm/i915: extract l3_parity substruct from dev_priv
...
Now intel_ddi_init is just like intel_hdmi_init and intel_dp_init: it
inits the encoder and then calls the proper init_connector functions.
Notice that for non-eDP ports we call both HDMI and DP connector init,
so we have 2 connectors attached to each DDI encoder.
After this change, intel_hdmi_init and intel_dp_init are only called
by Ivy Bridge and earlier, while hardware containing DDI outputs
should call intel_ddi_init.
Also added/removed quite a few "static" keywords due to the fact that
some function pointers were moved from intel_dp.c and intel_hdmi.c to
intel_ddi.c.
DP finally works on Haswell now! \o/
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both "intel_dp" and "intel_hdmi" structs had a "port" field, which
always had the same value. It makes more sense to move this to
intel_digital_port, so we can know the port independently of the
connector type.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When intel_hdmi_detect detects a monitor, set intel_encoder->type with
INTEL_OUTPUT_HDMI. Same for DP.
This should not break the current code because these variables never
change. This will be used after we create the DDI encoder because it
will have both DP and HDMI connectors.
We won't support eDP+HDMI on the same port, so if an encoder is eDP we
should expect it to always remain eDP and never change.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä
Dave Airlie
Chris Wilson
Paulo Zanoni
Damien Lespiau
Daniel Vetter
Rob Clark