Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers are currently used by mesa for blitting,
transform feedback extensions, and performance monitoring
extensions.
v2: REG64 macro
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec defines most of these commands as privileged. A few others,
like the semaphore mbox command and some display commands, are also
reserved for the driver's use. Subsequent patches relax some of
these restrictions.
v2: Rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add command tables defining irregular length commands for each ring.
This requires a few new command opcode definitions.
v2: Whitespace adjustment in command definitions, sparse fix for !F
OTC-Tracker: AXIA-4631
Change-Id: I064bceb457e15f46928058352afe76d918c58ef5
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
commit 93a25a9e2d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 6 09:40:43 2014 +0100
drm/i915: Disable full ppgtt by default
By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2
means full, all other values are reserved.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file contains all necessary defines, prototypes and typesdefs for
manipulating GEN graphics address translation (this does not include the
legacy AGP driver)
Reiterating the comment in the header,
"Please try to maintain the following order within this file unless it
makes sense to do otherwise. From top to bottom:
1. typedefs
2. #defines, and macros
3. structure definitions
4. function prototypes
Within each section, please try to order by generation in ascending
order, from top to bottom (ie. GEN6 on the top, GEN8 on the bottom)."
I've made some minor cleanups, and fixed a couple of typos while here -
but there should be no functional changes.
The purpose of the patch is to reduce clutter in our main header file,
making room for new growth, and make documentation of our interfaces
easier by splitting things out.
With a little more work, like making i915_gtt a pointer, we could
potentially completely isolate this header from i915_drv.h. At the
moment however, I don't think it's worth the effort.
Personally, I would have liked to put the PTE encoding functions in this
file too, but I didn't want to rock the boat too much.
A similar patch has been in use on my machine for some time. This exact
patch though has only been compile tested.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract all this logic into a new helper function
semaphore_wait_to_signaller_ring because:
- The current code has way too much magic.
- The current code doesn't look at bi16, which encodes VECS signallers
on HSW. Those are just added after the fact, so can't be encoded in
a neat formula.
- The current logic can't blow up since it limits its value range
sufficiently, but that's a bit too tricky to rely on in my opinion.
Especially when we start to add bdw support.
- I'm not a big fan of the explicit ring->semaphore_register list, but
I think it's more robust to use the same mapping both when
constructing the semaphore commands and when decoding them.
- Finally add a FIXME comment about lack of broadwell support here,
like in the earlier ipehr semaphore cmd detection function.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Actually drop the untrue claim in the commit message Chris
pointed out.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently not an issue since we don't emit sempahores, but better
not forget about those.
As a little prep work extract the ipehr decoding for cleaner control
flow. And apply a bit of polish.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gupta, Sourab" <sourab.gupta@intel.com>
Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because gen6_gt_force_wake_{get,put} should already be responsible for
getting/putting runtime PM. If we keep these calls, debugfs will not
be testing the get/put calls of the forcewake functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If runtime PM is enabled and we unset all modes, we will runtime
suspend after __intel_set_mode() , then function
intel_modeset_check_state() will try to read the HW state while it is
suspended and trigger lots of WARNs because it shouldn't be reading
registers.
So on this patch we make intel_ddi_connector_get_hw_state() return
false in case the power domain is disabled, and we also make
intel_display_power_enabled() return false in case the device is
suspended. Notice that we can't just use
intel_display_power_enabled_sw() because while the driver is being
initialized the power domain refcounts are not reflecting the real
state of the hardware.
Just for reference, I have previously published an alternate patch for
this problem, called "drm/i915: get runtime PM at intel_set_mode".
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At i915_display_info, don't call cursor_position() for a disabled
CRTC, since the CRTC may be on a powered down pipe, and this will
cause "Unclaimed register before interrupt" error messages.
Testcase: igt/pm_pc8/debugfs-read
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we may get some WARNs complaining that we're reading a
register while we're suspended.
Testcase: igt/pm_pc8/debugfs-read
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far force_wake_timer was only used by gen6_gt_force_wake_put. Since
we always had balanced gen6_gt_force_wake_get/put calls, we could
guarantee balanced calls to intel_runtime_pm_get/put.
Commit 8232644ccf, "drm/i915: Convert
the forcewake worker into a timer func" started scheduling the
force_wake_timer at gen6_read, which resulted in an unbalanced
runtime_pm refcount.
So this commit just reverts to the old behavior until we can find a
proper way to used delayed force_wake from the register read/write
macros without leaving the runtime_pm refcounts unbalanced and without
runtime suspending the driver while forcewake is active.
Testcase: igt/pm_pc8/rte
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76544
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin
Ben Widawsky
Ben Widawsky
Daniel Vetter
Chris Wilson
Paulo Zanoni
Imre Deak
Jani Nikula