An error before the hardif is found has to free the skb. But every error
after that has to free the skb + put the hard interface.
Fixes: 8def0be82d ("batman-adv: Consume skb in batadv_frag_send_packet")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_tt_prepare_tvlv_local_data can fail to allocate the memory for the
new TVLV block. The caller is informed about this problem with the returned
length of 0. Not checking this value results in an invalid memory access
when either tt_data or tt_change is accessed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
pull request for net-next: batman-adv 2016-11-08 v2
This feature and cleanup patchset includes the following changes:
- netlink and code cleanups by Sven Eckelmann (3 patches)
- Cleanup and minor fixes by Linus Luessing (3 patches)
- Speed up multicast update intervals, by Linus Luessing
- Avoid (re)broadcast in meshes for some easy cases,
by Linus Luessing
- Clean up tx return state handling, by Sven Eckelmann (6 patches)
- Fix some special mac address handling cases, by Sven Eckelmann
(3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases during shutdown the following general protection fault can
happen:
general protection fault: 0000 [#1] SMP
Modules linked in: batman_adv(O-) [...]
CPU: 3 PID: 1714 Comm: rmmod Tainted: G O 4.6.0-rc6+ #1
[...]
Call Trace:
[<ffffffffa0363294>] batadv_hardif_disable_interface+0x29a/0x3a6 [batman_adv]
[<ffffffffa0373db4>] batadv_softif_destroy_netlink+0x4b/0xa4 [batman_adv]
[<ffffffff813b52f3>] __rtnl_link_unregister+0x48/0x92
[<ffffffff813b9240>] rtnl_link_unregister+0xc1/0xdb
[<ffffffff8108547c>] ? bit_waitqueue+0x87/0x87
[<ffffffffa03850d2>] batadv_exit+0x1a/0xf48 [batman_adv]
[<ffffffff810c26f9>] SyS_delete_module+0x136/0x1b0
[<ffffffff8144dc65>] entry_SYSCALL_64_fastpath+0x18/0xa8
[<ffffffff8108aaca>] ? trace_hardirqs_off_caller+0x37/0xa6
Code: 89 f7 e8 21 bd 0d e1 4d 85 e4 75 0e 31 f6 48 c7 c7 50 d7 3b a0 e8 50 16 f2 e0 49 8b 9c 24 28 01 00 00 48 85 db 0f 84 b2 00 00 00 <48> 8b 03 4d 85 ed 48 89 45 c8 74 09 4c 39 ab f8 00 00 00 75 1c
RIP [<ffffffffa0371852>] batadv_purge_outstanding_packets+0x1c8/0x291 [batman_adv]
RSP <ffff88001da5fd78>
---[ end trace 803b9bdc6a4a952b ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: disabled
---[ end Kernel panic - not syncing: Fatal exception in interrupt
It does not happen often, but may potentially happen when frequently
shutting down and reinitializing an interface. With some carefully
placed msleep()s/mdelay()s it can be reproduced easily.
The issue is, that on interface removal, any still running worker thread
of a forwarding packet will race with the interface purging routine to
free a forwarding packet. Temporarily giving up a spin-lock to be able
to sleep in the purging routine is not safe.
Furthermore, there is a potential general protection fault not just for
the purging side shown above, but also on the worker side: Temporarily
removing a forw_packet from the according forw_{bcast,bat}_list will make
it impossible for the purging routine to catch and cancel it.
# How this patch tries to fix it:
With this patch we split the queue purging into three steps: Step 1),
removing forward packets from the queue of an interface and by that
claim it as our responsibility to free.
Step 2), we are either lucky to cancel a pending worker before it starts
to run. Or if it is already running, we wait and let it do its thing,
except two things:
Through the claiming in step 1) we prevent workers from a) re-arming
themselves. And b) prevent workers from freeing packets which we still
hold in the interface purging routine.
Finally, step 3, we are sure that no forwarding packets are pending or
even running anymore on the interface to remove. We can then safely free
the claimed forwarding packets.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv module has to be loaded to fulfill genl request by the
userspace. When it is not loaded then requests will fail. It is therefore
useful to get the module automatically loaded when such a request is made.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Things like VLANs don't have their link set when they are created. Thus
the wifi flags have to be evaluated later to fix their contents for the
link interface.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: re-add batadv_get_real_netdev to take rtnl
semaphore for batadv_get_real_netdevice]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In a few situations batman-adv tries to determine whether a given interface
is a WiFi interface to enable specific WiFi optimizations. If the interface
batman-adv has been configured with is a virtual interface (e.g. VLAN) it
would not be properly detected as WiFi interface and thus not benefit from
the special WiFi treatment.
This patch changes that by peeking under the hood whenever a virtual
interface is in play.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: integrate in wifi_flags caching, retrieve
namespace of link interface]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is requiring the type of wifi device in different contexts. Some
of them can take the rtnl semaphore and some of them already have the
semaphore taken. But even others don't allow that the semaphore will be
taken.
The data has to be retrieved when the hardif is added to batman-adv because
some of the wifi information for an hardif will only be available with rtnl
lock. It can then be cached in the batadv_hard_iface and the functions
is_wifi_netdev and is_cfg80211_netdev can just compare the correct bits
without imposing extra locking requirements.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP protocol requires cfg80211 to auto-detect the WiFi througput
to a given neighbor. Use batadv_is_cfg80211_netdev() to determine
whether or not an interface is eligible.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
An unicast batman-adv packet cannot be transmitted to a multicast or zero
mac address. So reject incoming packets which still have these classes of
addresses as destination mac address in the outer ethernet header.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The returned net_namespace of batadv_getlink_net may be used with functions
that potentially modify the struct. Thus it must return the pointer as
non-const like rtnl_link_ops::get_link_net does.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The routing check for management frames is validating the source mac
address in the outer ethernet header. It rejects every source mac address
which is a broadcast address. But it also has to reject the zero-mac
address and multicast mac addresses.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The routing checks are validating the source mac address of the outer
ethernet header. They reject every source mac address which is a broadcast
address. But they also have to reject any multicast mac addresses.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[sw@simonwunderlich.de: fix commit message typo]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
No caller of batadv_send_skb_to_orig is expecting the results to be -1
(-EPERM) anymore when the skbuff was not consumed. They will instead expect
that the skbuff is always consumed. Having such return code filter is
therefore not needed anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Receiving functions in Linux consume the supplied skbuff. Doing the same in
the batadv_rx_handler functions makes the behavior more similar to the rest
of the Linux network code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The throughput meter detects different situations as problems for the
current test. It stops the test after these and reports it to userspace.
This also has to be done when the primary interface disappeared during the
test.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 9799c50372 ("batman-adv: fix splat on disabling an interface")
fixed a warning but at the same time broke the rtnl function add_slave for
devices which were temporarily removed.
batadv_softif_slave_add requires soft_iface of and hard_iface to be NULL
before it is allowed to be enslaved. But this resetting of soft_iface to
NULL in batadv_hardif_disable_interface was removed with the aforementioned
commit.
Reported-by: Julian Labus <julian@freifunk-rtk.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending functions in Linux consume the supplied skbuff. Doing the same in
batadv_send_skb_to_orig avoids the hack of returning -1 (-EPERM) to signal
the caller that he is responsible for cleaning up the skb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sending functions in Linux consume the supplied skbuff. Doing the same in
batadv_frag_send_packet avoids the hack of returning -1 (-EPERM) to signal
the caller that he is responsible for cleaning up the skb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A failure during the submission also causes dropped packets.
batadv_interface_tx should therefore also increase the DROPPED counter for
these returns.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann
David S. Miller
Linus Lüssing
Sven Eckelmann
Marek Lindner