Use a syscon regmap to access the system timer registers.
Also, rename the driver atmel_st_watchdog to stop conflicting with
at91sam9_wdt.c
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The watchdog interrupt (only used when activating software watchdog)
shouldn't be suspended when entering suspend mode, because it is shared
with a timer device (which request the line with IRQF_NO_SUSPEND) and once
the watchdog "Mode Register" has been written, it cannot be changed (which
means we cannot disable the watchdog interrupt when entering suspend).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BCM5301X (ARCH_BCM_5301X) is a new Broadcom architecture using the same
SoC bus driver (bcma) as BCM47XX but based on ARM instead of MIPS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support to the jz4740 driver. Simple of_match_ptr. No other
modification for probe needed
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt_set_top() function takes in a value in seconds. In
dw_wdt_open() we were calling it with a value that's supposed to
represent the maximum value programmed into the "top" register with a
comment saying that we were trying to set the watchdog to its maximum
value. Instead we ended up setting the watchdog to ~15 seconds.
Let's fix this. However, setting things to the "max" gives me an 86
second watchdog in the system I'm looking at. 86 seconds feels a
little too long. We'll explicitly choose 30 seconds as a more
reasonable value.
NOTE: Ideally this driver should be transitioned to be a real watchdog
driver. Then we could use "watchdog_init_timeout" and let the timeout
be specified in a number of ways (device tree, module parameter, etc).
This patch should be considered a bit of a stopgap solution.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some dw_wdt implementations the "top" register may be initted to 0
at bootup. In such a case, each "pat" of the watchdog will reset the
timer to 0xffff. That's pretty short.
The input clock of the wdt can be any of a wide range of values. On
an rk3288 system, I've seen the wdt clock be 24.75 MHz. That means
each tick is ~40ns and we'll count to 0xffff in ~2.6ms.
Because of the above two facts, it's a really good idea to pat the
watchdog after initting the "top" register properly and before
enabling the watchdog. If you don't then there's no way we'll get the
next heartbeat in time.
Jisheng Zhang fixed this problem on some dw_wdt versions by using the
TOP_INIT feature. However, the dw_wdt on rk3288 doesn't have TOP_INIT
so it's a good idea to also pat the watchdog manually.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog functionality in both chips is almost identical to NCT6779.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Just like in case of other watchdog drivers, use the new kernel core
API to provide restart support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some chips, like the TPS386000, the trigger cannot be disabled
and the CPU must keep toggling the line at all times. Add a switch
"always_running" to keep toggling the GPIO line regardless of the
state of the soft part of the watchdog. The "armed" member keeps
track of whether a timeout must also cause a reset.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9063 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
The actual restart method was inspired by a platform-specific patch from
the BSP by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace device_reset() with devm_reset_control_get() + reset_control_deassert().
Make use of watchdog_init_timeout() instead of setting the timeout manually.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
allow_kdump was enabled as default since following commit.
commit a089361cf5,
watchdog: hpwdt: Unregister NMI events on exit.
But the initialization message was not modified.
So it still shows
HP Watchdog Timer Driver: NMI decoding initialized,
allow kernel dump: ON (default = 0/OFF) <=
This "default = 0/OFF" message may confuse users.
Fix it as "default = 1/ON".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
IT8783 watchdog works as in IT872x
Tested on Adlink cPCI-6520 boards
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
watchdog_ops const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Disable power down counter of the watchdog to avoid system resets. The
watchdog power down counter is set automatically by the chip. If it is
not set to 0 in the driver, the system resets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
If PM will be supported, please make sure that the wdev->clk
could disable the watchdog's counter input clock source or can
mask watchdog's reset request to the core.
If watchdog is still used by consumers and resumes from deep
sleep state, we need to restart the watchdog again without
enabling the timer.
If watchdog been has started --> stopped by the consumers and
resumes from non-deep sleep state, then start the timer again.
If watchdog has been started --> stopped by the consumers and
resumes from deep sleep state, will do nothing. The watchdog
will be restarted by consumers next time to be used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build warning by passing the expected argument type to
watchdog_active():
drivers/watchdog/imx2_wdt.c: In function 'imx2_wdt_suspend':
drivers/watchdog/imx2_wdt.c:340:2: warning: passing argument 1 of 'watchdog_active' from incompatible pointer type [enabled by default]
In file included from drivers/watchdog/imx2_wdt.c:38:0:
include/linux/watchdog.h:104:20: note: expected 'struct watchdog_device *' but argument is of type 'struct watchdog_device **'
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Alexandre Belloni
Boris BREZILLON
Rafał Miłecki
Zubair Lutfullah Kakakhel
Doug Anderson
Guenter Roeck
Mike Looijmans
Geert Uytterhoeven
Matthias Brugger
Tony Lindgren
John Crispin
Masanari Iida
Paolo Teti
Krzysztof Kozlowski
Naidu Tellapati
Wolfram Sang
Markus Pargmann
Xiubo Li
Fabio Estevam
Linus Torvalds