Core Changes:
- Add quirk for LGD 764 panel to default 10bpc (Mario)
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
* tag 'drm-misc-next-fixes-2017-05-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/edid: Add 10 bpc quirk for LGD 764 panel in HP zBook 17 G2
These were ineffective due to touching the list without the alarm lock,
but should no longer be required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
The idea here was to avoid having to "manually" program the HW if there's
a new earliest alarm. This was lazy and bad, as it leads to loads of fun
races between inter-related callers (ie. therm).
Turns out, it's not so difficult after all. Go figure ;)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
At least therm/fantog "attempts" to work around this issue, which could
lead to corruption of the pending alarm list.
Fix it properly by not updating the timestamp without the lock held, or
trying to add an already pending alarm to the pending alarm list....
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
If the time to the next alarm is short enough, we could race with HW and
end up with an ~4 second delay until it triggers.
Fix this by checking again after we update HW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Fixes a race where we can miss an alarm that triggers while we're already
processing previous alarms.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
object->engine cannot be NULL, it's either valid, or an error pointer.
This particular condition shouldn't actually be possible, but just in
case, we'll keep it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This reg has moved on Pascal, and causes a bus fault.
We never use the value anyway, so just remove the read.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DRM core used to only call prepare_fb/cleanup_fb() when a plane's
framebuffer changed, which achieved the desired effect.
It's apparently now up to the driver to decide on its own.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.11+]
This "optimisation" (which was originally meant to skip updating cursor
settings in the core channel on position-only updates) turned out to be
pointless in the final design of the code before it was merged.
Remove it completely, as it breaks other cases.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.10+]
Pull more documentation updates from Jonathan Corbet:
"Connect the newly RST-formatted documentation to the rest; this had to
wait until the input pull was done. There's also a few small fixes
that wandered in"
* tag 'docs-4.12-2' of git://git.lwn.net/linux:
doc: replace FTP URL to kernel.org with HTTPS one
docs: update references to the device io book
Documentation: earlycon: fix Marvell Armada 3700 UART name
docs-rst: add input docs at main index and use kernel-figure
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, just a couple of small bugfixes,
improvements and cleanups.
- fix handling of probing errors in omapfb (Arvind Yadav)
- remove incorrect __exit markups in few drivers (Dmitry Torokhov)
- fix boot time logo support for drivers using deferred probe
(Takeshi Kihara)
- fix DMA allocation size for ARM CLCD driver (Liam Beguin)
- add support for specifying size via xenstore in xen-frontfb
(Juergen Gross)
- support for AUS mode in imxfb driver (Martin Kaiser)
- fix buffer on stack usage in udlfb driver (Maksim Salau)
- probe failure path fixup in sm501fb driver (Alexey Khoroshilov)
- fix config dependency loop for stifb driver (Arnd Bergmann)
- misc cleanups (Joe Perches, Christophe Leroy, Karim Eshapa, Pushkar
Jambhlekar)"
* tag 'fbdev-v4.12' of git://github.com/bzolnier/linux:
fbdev: sti: don't select CONFIG_VT
drivers/video/fbdev/omap/lcd_mipid.c: Use time comparison kernel macros
sm501fb: don't return zero on failure path in sm501fb_start()
video: fbdev: udlfb: Fix buffer on stack
video: console: Remove reference to CONFIG_8xx
dt-bindings: display: imx: entry for AUS mode
video: fbdev: imxfb: support AUS mode
drivers/video/fbdev: Fixing coding guidelines in acornfb.c
xen, fbfront: add support for specifying size via xenstore
video: ARM CLCD: fix dma allocation size
drivers/video: Convert remaining uses of pr_warning to pr_warn
video/logo: tidyup fb_logo_late_init initcall timing
video: fbdev: i810: remove incorrect __exit markups
video: fbdev: pmag-aa-fb: remove incorrect __exit markups
video: fbdev: pmagb-b-fb: remove incorrect __exit markups
video: fbdev: pmag-ba-fb: remove incorrect __exit markups
omapfb: dss: Handle return errors in dss_init_ports()
Pull block fixes from Jens Axboe:
"A smaller collection of fixes that should go into -rc1. This contains:
- A fix from Christoph, fixing a regression with the WRITE_SAME and
partial completions. Caused a BUG() on ppc.
- Fixup for __blk_mq_stop_hw_queues(), it should be static. From
Colin.
- Removal of dmesg error messages on elevator switching, when invoked
from sysfs. From me.
- Fix for blk-stat, using this_cpu_ptr() in a section only protected
by rcu_read_lock(). This breaks when PREEMPT_RCU is enabled. From
me.
- Two fixes for BFQ from Paolo, one fixing a crash and one updating
the documentation.
- An error handling lightnvm memory leak, from Rakesh.
- The previous blk-mq hot unplug lock reversal depends on the CPU
hotplug rework that isn't in mainline yet. This caused a lockdep
splat when people unplugged CPUs with blk-mq devices. From Wanpeng.
- A regression fix for DIF/DIX on blk-mq. From Wen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: handle partial completions for special payload requests
blk-mq: NVMe 512B/4K+T10 DIF/DIX format returns I/O error on dd with split op
blk-stat: don't use this_cpu_ptr() in a preemptable section
elevator: remove redundant warnings on IO scheduler switch
block, bfq: stress that low_latency must be off to get max throughput
block, bfq: use pointer entity->sched_data only if set
nvme: lightnvm: fix memory leak
blk-mq: make __blk_mq_stop_hw_queues static
lightnvm: remove unused rq parameter of nvme_nvm_rqtocmd() to kill warning
block/mq: fix potential deadlock during cpu hotplug
FTP services were shutdown some weeks ago, so the FTP URL
does not work anymore. Fix this by replacing it with
corresponding HTTPS URL.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
SCSI devices can return short writes on Write Same just like for normal
writes, so we need to handle this case for our special payload requests
as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When booted as pv-guest the p2m list presented by the Xen is already
mapped to virtual addresses. In dom0 case the hypervisor might make use
of 2M- or 1G-pages for this mapping. Unfortunately while being properly
aligned in virtual and machine address space, those pages might not be
aligned properly in guest physical address space.
So when trying to obtain the guest physical address of such a page
pud_pfn() and pmd_pfn() must be avoided as those will mask away guest
physical address bits not being zero in this special case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
When running as Xen pv guest X86_BUG_SYSRET_SS_ATTRS must not be set
on AMD cpus.
This bug/feature bit is kind of special as it will be used very early
when switching threads. Setting the bit and clearing it a little bit
later leaves a critical window where things can go wrong. This time
window has enlarged a little bit by using setup_clear_cpu_cap() instead
of the hypervisor's set_cpu_features callback. It seems this larger
window now makes it rather easy to hit the problem.
The proper solution is to never set the bit in case of Xen.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
When CONFIG_ARM64_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_ARM_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If the caller has set __GFP_NOWARN don't print the following message:
vmap allocation for size 15736832 failed: use vmalloc=<size> to increase
size.
This can happen with the ARM/Linux or ARM64/Linux module loader built
with CONFIG_ARM{,64}_MODULE_PLTS=y which does a first attempt at loading
a large module from module space, then falls back to vmalloc space.
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As of commits d8f347ba35cf ("nios2: enable earlycon support"),
0dcc0542a0 ("serial: altera_jtaguart: add earlycon support") and
4d9d7d896d ("serial: altera_uart: add earlycon support"), the nios2
architecture and the altera_uart/altera_jtaguart drivers support
earlycon. Thus, the custom early console implementation for nios2 is no
longer necessary to get early boot messages. Remove it and rely fully on
earlycon support.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
This reverts commit 0e2eb7d12e
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Thu Mar 30 10:12:39 2017 -0700
target: Fix VERIFY and WRITE VERIFY command parsing
This patch broke existing behaviour for WRITE_VERIFY because
it dropped the original SCF_SCSI_DATA_CDB assignment for
bytchk = 0 so target_cmd_size_check() no longer rejected
this case, allowing an overflow case to trigger an OOPs
in iscsi-target.
Since the short term and long term fixes are still being
discussed, revert it for now since it's late in the merge
window and try again in v4.13-rc1.
Conflicts:
drivers/target/target_core_sbc.c
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dave Airlie
Ben Skeggs
Linus Torvalds
Michael Heimpold
Christoph Hellwig
Juergen Gross
Florian Fainelli
Tobias Klauser
Nicholas Bellinger