Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.16 development
cycle:
- Antoine Tenart made the get_group_pins() vtable entry optional.
- Antoine also provides an entirely new driver for the Marvell Berlin
SoC. This is unrelated to the existing MVEBU hardware driver and
warrants its own separate driver.
- reflected from the GPIO subsystem there is a number of refactorings
to make pin control drivers with gpiochips use the new gpiolib
irqchip helpers. The following drivers were converted to use the
new infrastructure:
* ST Microelectronics STiH416 and friends
* The Atmel AT91
* The CSR SiRF (Prima2)
* The Qualcomm MSM series
- massive improvements in the Qualcomm MSM driver from Bjorn
Andersson, Andy Gross and Kumar Gala. Among those new support for
the IPQ8064 and MSM8x74 SoC variants.
- support for the Freescale i.MX6 SoloX SoC variant.
- massive improvements in the Allwinner sunxi driver from Boris
Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori Morimoto,
Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from Stepgen
Warren.
- the Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- the MVEBU driver now supports the Orion5x SoC variants, which is
part of the effort of getting rid of the old Marvell kludges in
arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- a ton of cleanups and janitorial patches from Axel Lin.
- some minor fixes and improvements here and there"
* tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: sirf: fix a bad conflict resolution
pinctrl: msm: Add more MSM8X74 pin definitions
pinctrl: qcom: ipq8064: Fix naming convention
pinctrl: msm: Add missing sdc1 and sdc3 groups
pinctrl: sirf: switch to using allocated state container
pinctrl: Enable "power-source" to be extracted from DT files
pinctrl: sunxi: create irq/pin mapping during init
pinctrl: pinconf-generic: Use kmemdup instead of kmalloc + memcpy
pinctrl: berlin: Use devm_ioremap_resource()
pinctrl: sirf: fix typo for GPIO bank number
pinctrl: sunxi: depend on RESET_CONTROLLER
pinctrl: sunxi: fix pin numbers passed to register offset helpers
pinctrl: add pinctrl driver for imx6sx
pinctrl/at91: Fix lockup when IRQ on PIOC and PIOD occurs
pinctrl: msm: switch to using generic GPIO irqchip helpers
pinctrl: sunxi: Fix multiple registration issue
pinctrl: sunxi: Fix recursive dependency
pinctrl: berlin: add the BG2CD pinctrl driver
pinctrl: berlin: add the BG2 pinctrl driver
pinctrl: berlin: add the BG2Q pinctrl driver
...
Commit 294d1351ff
"pinctrl: sirf: switch to using allocated state container"
caused a build conflict due to a bad conflict resolution
when cherry-picking the patch. Fix it up.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rewrites the SIRF pinctrl driver to allocate a state container
for the GPIO chip, just as is done for the pin controller, and
use the gpiochip_add_pin_range() to add the range from the gpiochip
side rather than adding the range from the pinctrl side.
All resulting changes are done in order to pass around a state
container rather than refer to a static global object.
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq/pin mapping is used to lookup the pin to mux to the irq
function when the irq is enabled. It is created when gpio_to_irq
is called. Creating the mapping during init allows us to map the
interrupts directly from the device tree.
Originally the IRQ to pin mapping was created when gpio_to_irq
was called with a GPIO handle. The mapping in turn is used to mux
the pin into EINT mode.
If the mapping is created during gpio_to_irq, we can't use the
interrupts directly, i.e. through the DT with "interrupts = <&pio A 4>".
Instead we'd have to use "gpios = <&pio A B>", then pass the gpio
through to gpio_to_irq.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 7420d2d09b: "pinctrl: sirf: switch driver to use gpiolib
irqchip helpers" from Apr 15, 2014, leads to the following static
checker warning:
drivers/pinctrl/sirf/pinctrl-sirf.c:578 sirfsoc_gpio_handle_irq()
warn: buffer overflow 'sgpio_chip.sgpio_bank' 5 <= 31
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 R_PIO driver depends on the reset framework in a mandatory way. Express
this by adding a depends on the reset framework in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin numbers passed to sunxi_*_reg helpers to get the correct
registers should be the pin offset for the PIO block, not the
absolute number we use that is based on the alphanumeric labels
Allwinner uses.
This patch subtracts .pin_base from the pin number passed to these
functions, so the driver accesses the correct registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With commit 80cc3732 (pinctrl/at91: convert driver to use gpiolib irqchip)
gpiochip_set_chained_irqchip is called for PIOC, PIOD and PIOE. The
associated GPIO chip for the IRQ chip is overwritten each time, because
they share the same hard IRQ line.
Thus if an IRQ occurs on PIOC or PIOD, gpio_irq_handler will only check on
PIOE (the assigned GPIO chip) where no event occured. Thus the IRQ will
not be cleared, retriggering the ISR.
Fix that (like done before) by only set the PIOC GPIO chip to the IRQ chip
and walk the list in the irq handler.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the support for the PRCM muxer on the A31 has been added, the global
static pinctl_desc definition has been left as is. Unfortunately, this
structure is used to register the pinctrl device, and prior to this
registration, we set the name and pins field.
Since this structure is shared across instances, that means that the latest
registered pinctrl device wins in setting the name, pins and pins numbers,
which is not really a good thing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following configuration error:
drivers/pinctrl/sunxi/Kconfig:3:error: recursive dependency detected!
drivers/pinctrl/sunxi/Kconfig:3: symbol PINCTRL_SUNXI is selected by PINCTRL_SUN4I_A10
drivers/pinctrl/sunxi/Kconfig:9: symbol PINCTRL_SUN4I_A10 default value contains PINCTRL_SUNXI
Add a new intermedia PINCTRL_SUNXI_COMMON, that superseeds the PINCTRL_SUNXI
one.
We still need to keep PINCTRL_SUNXI at the moment in order to preserve
bisectability. Indeed, during that merge window, we also introduced the
MACH_SUN* symbols. Since it's going through different trees, we can't rely on
the fact that the options will be there, while ARCH_SUNXI still select
PINCTRL_SUNXI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2 SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If chip->to_irq is NULL ACPI GPIO helpers don't register GPIO event
handlers thus preventing any ACPI GPIO triggered events. Solve this by
calling gpiochip_add() after we have set up drivers chip->to_irq hook.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds
Linus Walleij
Andy Gross
Kumar Gala
Bjorn Andersson
Ivan T. Ivanov
Chen-Yu Tsai
Benoit Taine
Jingoo Han
Barry Song
Maxime Ripard
Anson Huang
Alexander Stein
Antoine Tenart
Mika Westerberg
Jin Yao