Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately. The fix is to
leave lazy mode when doing a vmalloc sync.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I did some testing and found quite a lot of problems (doesn't
boot at all on non NUMA and misassigns cores on Opteron systems).
Mark it as experimental and warn against its use for now.
It's still default y for SUMMIT/NUMAQ because it'll presumably
work on these systems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit ab144f5ec6 the patching code
now collects the complete new instruction stream into a temp buffer
before finally patching in the new insns. In some cases the paravirt
patchers will choose to leave the patch site unpatched (length mismatch,
clobbers mismatch, etc).
This causes the new patching code to copy an uninitialized temp buffer,
i.e. garbage, to the callsite. Simply make sure to always initialize
the buffer with the original instruction stream. A better fix is to
audit all the patchers and return proper length so that apply_paravirt()
can skip copies when we leave the patch site untouched.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When filling in the MBR signature array, the setup code failed to advance
boot_params.edd_mbr_sig_buf_entries, which resulted in the valid data
being ignored.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
At least one machine has been identified in the field which advertises
EDD for all drives but locks up if one attempts an extended read from
a non-primary drive.
The MBR is always at CHS 0-0-1, so there is no reason to use an
extended read, other than the possibility that the BIOS cannot handle
it.
Although this might break as many machines as it fixes (a small number
either way), the current state is a regression but the reverse is not.
Therefore revert to the previous state of not using extended read.
Quite probably the Right Thing to do is to read using plain (CHS) read
and extended read on failure, but that change would definitely have to
go through -mm first.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The current display page is an 8-bit number, even though struct
screen_info gives it a 16-bit number. The number is returned in %bh,
so it needs to be >> 8 before storing.
Special thanks to Jeff Chua for detailed bug reporting.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Level type interrupts do not need to be resent. It was also found that
some chipsets get confused in case of the resend.
Mark the ioapic level type interrupts as such to avoid the resend
functionality in the generic irq code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
ACPI: thermal: add DMI hooks to handle AOpen's broken Award BIOS
ACPI: thermal: create "thermal.act=" to disable or override active trip point
ACPI: thermal: create "thermal.nocrt" to disable critical actions
ACPI: thermal: create "thermal.psv=" to override passive trip points
ACPI: thermal: expose "thermal.tzp=" to set global polling frequency
ACPI: thermal: create "thermal.off=1" to disable ACPI thermal support
ACPI: thinkpad-acpi: fix sysfs paths in documentation
ACPI: static
ACPI EC: remove potential deadlock from EC
ACPI: dock: Send key=value pair instead of plain value
ACPI: bay: send envp with uevent - fix
acpi-cpufreq: Fix some x86/x86-64 acpi-cpufreq driver issues
ACPI: fix "Time Problems with 2.6.23-rc1-gf695baf2"
ACPI: thinkpad-acpi: change thinkpad-acpi input default and kconfig help
ACPI: EC: fix run-together printk lines
ACPI: sbs: remove dead code
ACPI: EC: acpi_ec_remove(): fix use-after-free
ACPI: EC: Switch from boot_ec as soon as we find its desc in DSDT.
ACPI: EC: fix build warning
ACPI: EC: If ECDT is not found, look up EC in DSDT.
...
The new percpu code has apparently broken the doublefault handler
when CONFIG_DEBUG_SPINLOCK is set. Doublefault is handled by
a hardware task, making the check
SPIN_BUG_ON(lock->owner == current, lock, "recursion");
fault because it uses the FS register to access the percpu data
for current, and that register is zero in the new TSS. (The trace
I saw was on 2.6.20 where it was GS, but it looks like this will
still happen with FS on 2.6.22.)
Initializing FS in the doublefault_tss should fix it.
AK: Also fix broken ptr_ok() and turn printks into KERN_EMERG
AK: And add a PANIC prefix to make clear the system will hang
AK: (e.g. x86-64 will recover)
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Averatec 2370 and some other Turion laptop BIOS seems to program the
ENABLE_C1E MSR inconsistently between cores. This confuses the lapic
use heuristics because when C1E is enabled anywhere it seems to affect
the complete chip.
Use a global flag instead of a per cpu flag to handle this.
If any CPU has C1E enabled disabled lapic use.
Thanks to Cal Peake for debugging.
Cc: tglx@linutronix.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 19d36ccdc3 "x86: Fix alternatives
and kprobes to remap write-protected kernel text" uses code which is
being patched for patching.
In particular, paravirt_ops does patching in two stages: first it
calls paravirt_ops.patch, then it fills any remaining instructions
with nop_out(). nop_out calls text_poke() which calls
lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val):
that call site is one of the places we patch.
If we always do patching as one single call to text_poke(), we only
need make sure we're not patching the memcpy in text_poke itself.
This means the prototype to paravirt_ops.patch needs to change, to
marshal the new code into a buffer rather than patching in place as it
does now. It also means all patching goes through text_poke(), which
is known to be safe (apply_alternatives is also changed to make a
single patch).
AK: fix compilation on x86-64 (bad rusty!)
AK: fix boot on x86-64 (sigh)
AK: merged with other patches
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out CLFLUSH support is still not complete; we
flush the wrong pages. Again disable it for the release.
Noticed by Jan Beulich who then also noticed a stupid typo later.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some broken devices have been discovered to require %al/%ax/%eax registers
for MMIO config space accesses. Modify mmconfig.c to use these registers
explicitly (rather than modify the global readb/writeb/etc inlines).
AK: also changed i386 to always use eax
AK: moved change to extended space probing to different patch
AK: reworked with inlines according to Linus' requirements.
AK: improve comments.
Signed-off-by: dean gaudet <dean@arctic.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch finishes the i386 and x86-64 ->sysdata conversion and hopefully
also fixes Riku's and Andy's observed bugs. It is based on Yinghai Lu's
and Andy Whitcroft's patches (thanks!) with some changes:
- introduce pci_scan_bus_with_sysdata() and use it instead of
pci_scan_bus() where appropriate. pci_scan_bus_with_sysdata() will
allocate the sysdata structure and then call pci_scan_bus().
- always allocate pci_sysdata dynamically. The whole point of this
sysdata work is to make it easy to do root-bus specific things
(e.g., support PCI domains and IOMMU's). I dislike using a default
struct pci_sysdata in some places and a dynamically allocated
pci_sysdata elsewhere - the potential for someone indavertantly
changing the default structure is too high.
- this patch only makes the minimal changes necessary, i.e., the NUMA node is
always initialized to -1. Patches to do the right thing with regards
to the NUMA node can build on top of this (either add a 'node'
parameter to pci_scan_bus_with_sysdata() or just update the node
when it becomes known).
The patch was compile tested with various configurations (e.g., NUMAQ,
VISWS) and run-time tested on i386 and x86-64. Unfortunately none of my
machines exhibited the bugs so caveat emptor.
Andy, could you please see if this fixes the NUMA issues you've seen?
Riku, does this fix "pci=noacpi" on your laptop?
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: <riku.seppala@kymp.net>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses some issues in x86/x86-64 acpi-cpufreq driver:
1. Current memory allocation for acpi_perf_data is actually open-coded
alloc_percpu(). The patch defines and handles acpi_perf_data as percpu
data. The code will be cleaner and easier to be maintained with this
change.
2. Won't load driver in acpi_cpufreq_early_init() failure case.
3. Add __init for acpi_cpufreq_early_init().
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a missing =m constraint to the EDD-probing code, that could have
caused improper dead-code elimination.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add memory operand constraint and write-only modifier to the inline
assembly to effect the writing of the EDID block to boot_params.edid_info.
Without this, gcc would think the EDID query was dead code and would
eliminate it.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] EDD: Fix the computation of the MBR sector buffer
[x86 setup] Newline after setup signature failure message
x86 boot code comments typos
Zachary Amsden
Andi Kleen
Chris Wright
Daniel Gollub
Jan Engelhardt
H. Peter Anvin
Thomas Gleixner
Linus Torvalds
Len Brown
Chuck Ebbert
Adrian Bunk
dean gaudet
Muli Ben-Yehuda
Fenghua Yu
Antonino A. Daplas