The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine. So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.
This bug does not happen when NAPI disabled. After txdone there
must be at least one free tx slot. But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.
In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the frame control for ieee80211_is_data_qos() is true before
counting the number of tfds can be free, the tfds_in_queue only
increment when ieee80211_is_data_qos() is true before transmit; so it
should only decrement if the type match.
Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid
invalid information pass from uCode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive reply_tx and ready to decrement the count for number of
tfds in queue, do error checking to prevent error condition and
tfds_in_queue become negative number.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.
Based on a review of the chip datasheets and advice from the designer
of these boards:
- Raise the maximum board temperatures to the specified maximum ambient
temperatures for their PHYs plus the expected temperature bias of the
board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol. It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.
This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"
The particular setting in which I noticed this was monitor mode:
iwconfig wlan0 mode monitor
ifconfig wlan0 up
./iw wlan0 set channel 64 HT40-
#./iw wlan0 set channel 64 HT40-
tcpdump -i wlan0 -y IEEE802_11_RADIO
would only catch HT40 packets if I issued the IW command twice.
From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before sending a command to the ASIC, set version properly.
This is necessary for the ARM firmware to send correct data to the driver.
This also fixes a bug in certain skews of the ASIC where the statistics
are misreported.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to have the WUS register set to all 1's in order for the hardware
to be capable of ever waking up. Set it here in the ixgbe_probe().
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82598 has an erratum that receipt of pause frames at 1G
could lead to a Tx Hang. To avoid this this patch disables
Rx FC while at 1G speed for all 82598 parts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Atsushi Nemoto
Torgny Johansson
Anton Blanchard
Stanislaw Gruszka
Wey-Yi Guy
Ben Hutchings
Dan Halperin
Ajit Khaparde
Don Skidmore
Steve Hodgson
Shanyu Zhao
Simon Kagstrom
Jelle Martijn Kok
Roel Kluin
Sujith
Julia Lawall
Divy Le Ray