* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (132 commits)
sh: oprofile: Fix up the module build.
sh: add UIO support for JPU on SH7722.
serial: sh-sci: Fix up port pinmux for SH7366.
sh: mach-rsk: Use uImage generation by default for rsk7201/7203.
sh: mach-sh03: Fix up pata_platform build breakage.
sh: enable deferred io LCDC on Migo-R
video: sh_mobile_lcdcfb deferred io support
video: deferred io with physically contiguous memory
video: deferred io cleanup
video: fix deferred io fsync()
sh: add LCDC interrupt configuration to AP325 and Migo-R
sh_mobile_lcdc: use FB_SYS helpers instead of FB_CFB
sh: split coherent pages
sh: dma: Kill off ISA DMA wrapper.
sh: Conditionalize the code dumper on CONFIG_DUMP_CODE.
sh: Kill off the unused SH_ALPHANUMERIC debug option.
sh: Enable skipping of bss on debug platforms for sh32 also.
doc: Update sh cpufreq documentation.
sh: mrshpc_setup_windows() needs to be inline.
serial: sh-sci: sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL.
...
Fix a NULL pointer dereference that would occur if the video decoder tied to
the em28xx supports the VIDIOC_INT_RESET call (for example: the cx25840 driver)
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The v4l_compat_ioctl32() function only tested for the presence of the
ioctl op, not for unlocked_ioctl. So it would always return an error
when used with drivers that use unlocked_ioctl instead of ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the tuner modules were moved to common/tuners, a separate customize
option were added for tuners. However, the automatic selection of the
tuners were still using the older option.
This causes that the automatic selection to fail, if DVB_FE_CUSTOMISE is
selected. Also, since those tuners are now under MEDIA_TUNER_CUSTOMIZE
menu, if you unset MEDIA_TUNER_CUSTOMIZE, you can't manually select the
tuners.
This patch fixes this error by replacing DVB_FE_CUSTOMISE by
MEDIA_TUNER_CUSTOMIZE on all places were a tuner is selected.
The patch were generated by this small script:
for i in `find drivers/media -name Kconfig`; do
cat $i|perl -ne 's/(MEDIA_TUNER.*)DVB_FE_CUSTOMISE/\1MEDIA_TUNER_CUSTOMIZE/; print $_' >a
mv a $i
done
Also, manually reordered the tuner entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At some point the Flexcop driver was changed to support newer Flexcop cards.
These modifications however broke the detection of Cablestar 2 DVB-C cards.
The reason is that the earlier version of the driver used to retry
unsuccessful i2c operations. The demodulator of Cablestar 2 cards (stv0297)
seems to be very dependent on these retries and adding them back fixes
Cablestar detection.
This patch restores this behaviour for the CableStar2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user noticed that there would continue to be 4-6 keypresses even after the
user stopped holding down the button. This was because we were not reading
the bulk pipe faster than the firmware was injecting information, which would
result in a backlog.
Make the query interval faster, and increase the number of cycles before we
start repeating to compensate.
Thanks to Knud Poulsen <knud.poulsen@nokia.com> for pointing this out.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 50f3beb50a fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer versions of hald tries to open it to call QUERYCAP.
Due to the lack of a proper locking, it is possible to open the device
before it finishes initialization.
This patch adds a lock to avoid this risk, and to protect the list of
em28xx devices.
While here, remove the uneeded BKL lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't reconnect device in the USB-bus. Reconnect command was not
executed every time by device firmware and that causes harm.
Reconnection is not needed so remove it.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we have a polling task for IR, there's a race condition, since
IR can be polling while other operations are being doing. Also, we are
now sharing the same urb_buf for both read and write control urb
operations. So, we need a mutex.
Thanks to Davin Heitmueller <devin.heitmueller@gmail.com> for warning me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manu Abraham
Jean-Francois Moine
Linus Torvalds
Devin Heitmueller
Paul Mundt
Magnus Damm
Hans Verkuil
Mauro Carvalho Chehab
Jim Paris
Antti Seppälä
Devin Heitmueller
Wang Chen
David S. Miller
Douglas Schilling Landgraf
Michael Krufky
Jose Alberto Reguero