Make sure the erase_pending_wbuf_list's blocks are taken into account
when picking the block to GC.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the corresponding function to mark Superblock dirty instead
of doing it directly.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix fairly sad NOR-specific bug - during FS building ic->scan_dents
isn't zero, but jffs2_mark_node_obsolete() migt be called it tries to
finde the ic corresponding to ref - this requires ic->scan_dents = 0.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't remove inocache for inodes which are in read_inode() or
clear_inode() until they're done.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Look the ref->next_phys field instead of ->next_in_ino to determine
if the block has more then one node.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch replaces the current CONFIG_JFFS2_FS_NAND, CONFIG_JFFS2_FS_NOR_ECC
and CONFIG_JFFS2_FS_DATAFLASH with a single configuration option -
CONFIG_JFFS2_FS_WRITEBUFFER.
The only functional change of this patch is that the slower div/mod
calculations for SECTOR_ADDR(), PAGE_DIV() and PAGE_MOD() are now always
used when CONFIG_JFFS2_FS_WRITEBUFFER is enabled.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For Dataflash, can_mark_obsolete = false and the NAND write buffering
code (wbuf.c) is used.
Since the DataFlash chip will automatically erase pages when writing,
the cleanmarkers are not needed - so cleanmarker_oob = false and
cleanmarker_size = 0
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). The SECTOR_ADDR macro (added in the previous core patch) is
replaced with a (slower) div/mod version if CONFIG_JFFS2_FS_DATAFLASH is
selected.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). There are a few places in JFFS2 code where sector_size is used
as a bitmask. A new macro (SECTOR_ADDR) was defined to calculate these
sector addresses. For non-DataFlash devices, the original (faster)
bitmask operation is still used.
In scan.c, the EMPTY_SCAN_SIZE was a constant of 1024.
Since this could be larger than the sector size of the DataFlash, this
is now basically set to MIN(sector_size, 1024).
Addition of a jffs2_is_writebuffered() macro.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prevent deadlock when checking erased block for
space allocation during wbuf recovery.
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
avoid segfault when nextblock was refiled because of a write failure
- avoid filing blocks on the clean list when they have wasted
space
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- block refiling when writing directly to flash a buffer
which is bigger than wbuf
- retry cases for flushing wbuf
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Correction of retry case to avoid silent failure of rmdir
when jffs2_wbuf_recover GCs the previous entry (+ corresponding
dnode case).
Signed-off-by: Estelle Hammache <estelle.hammache@st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid "Eep. No valid nodes for ino #1" message for just-created filesystem.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid console spam with ext3 aborted journal.
ext3 usually reports error conditions that it detects in its environment.
But when its journal gets aborted due to such errors, it can sometimes
continue to report that condition forever, spamming the console to such
an extent that the initial first cause of the journal abort can be lost.
When the journal aborts, we put the filesystem into readonly mode. Most
subsequent filesystem operations will get rejected immediately by checks
for MS_RDONLY either in the filesystem or in the VFS. But some paths do
not have such checks --- for example, if we continue to write to a file
handle that was opened before the fs went readonly. (We only check for
the ROFS condition when the file is first opened.) In these cases, we
can continue to generate log errors similar to
EXT3-fs error (device $DEV) in start_transaction: Journal has aborted
for each subsequent write.
There is really no point in generating these errors after the initial
error has been fully reported. Specifically, if we're starting a
completely new filesystem operation, and the filesystem is *already*
readonly (ie. the ext3 layer has already detected and handled the
underlying jbd abort), and we see an EROFS error, then there is simply
no point in reporting it again.
Signed-off-by: Stephen Tweedie <sct@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If block_read_full_page() detects an error when running get_block() it will
run SetPageError(), then it will zero out the block in pagecache and will mark
the buffer_head uptodate.
So at the end of readahead we end up with a non-uptodate pagecache page which
is marked PageError. But it has uptodate buffers.
The pagefault code will run ClearPageError, will launch readpage a second time
and block_read_full_page() will notice the uptodate buffers and will mark the
page uptodate as well. We end up with an uptodate, !PageError page full of
zeros and the error is lost.
(It seems a little odd that filemap_nopage() runs ClearPageError(). I guess
all of this adds up to meaning that for each attempted access to the page, the
pagefault handler will retry the I/O. Which is good and bad. If the app is
ignoring SIGBUS for some reason we could get a lot of back-to-back I/O
errors.)
Fix it by not marking the pagecache buffer_head as uptodate if the attempt to
map that buffer to a disk block failed.
Credit-to: Qu Fuping <fs@ercist.iscas.ac.cn>
For reporting the bug and identifying its source.
Signed-off-by: Qu Fuping <fs@ercist.iscas.ac.cn>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
VmallocTotal: 34359738367 kB
VmallocUsed: 266288 kB
VmallocChunk: 18014366299193295 kB
is unsettling - x86_64 and some other architectures keep a separate address
range for modules in vmalloc's vmlist, which /proc/meminfo should pass over.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Woodhouse
Artem B. Bityuckiy
Andrew Victor
Estelle Hammache
Todd Poynor
Stephen Tweedie
Andrew Morton
Hugh Dickins