HCI_UART_PROTO_SET flag is set before hci_uart_set_proto call. If we
receive data from tty layer during this procedure, proto pointer may
not be assigned yet, leading to null pointer dereference in rx method
hci_uart_tty_receive.
This patch fixes this issue by introducing HCI_UART_PROTO_READY flag in
order to avoid any proto operation before proto opening and assignment.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver implements support for iBT2.1 Bluetooth controller embedded
in the AG620 communication combo. The controller needs to be configured
with bddata and can be patched with a binary patch file (pbn).
These operations are performed in manufacturing mode.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
rx_lock spinlock is only used in hci_uart_tty_receive() which is the
receive_buf ldisc callback.
hci_uart_tty_receive() is protected from re-entrance by its only
caller (flush_to_ldisc() in drivers/tty/tty_buffer.c) which held a
mutex (buf->lock) for this section.
This lock allows "safe use of the line discipline's receive_buf()
method by excluding the buffer work and any pending flush from using
the flip buffer." (comments from tty_buffer_lock_exclusive() in
drivers/tty/tty_buffer.c)
So, no need to double protect this resource with rx_lock.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA61x4 chips have supported sleep feature using In-Band-Sleep commands
to enable sleep feature based on H4 protocol. After sending
patch/nvm configuration is done, IBS mode will be up and running
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix for Cleanpatch warning:
Space prohibited between function name and open parenthesis '('
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.
Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hu->proto->*speed will always be used for all device where it is set.
But hu->*speed should be used if exist, so the test should be swapped.
The equivalent change is needed in bcm_setup() of hci_bcm.c.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added the ability to flow control the UART, improved the UART baud
rate setting, transferred the speeds into line discipline from the
protocol and introduced the tty init function.
Signed-off-by: Ilya Faenson <ifaenson@broadcom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the protocol support for Broadcom based UART devices to
enable firmware and patchram download procedure. It is a pretty
straight forward H:4 driver with the exception of actually having
its own setup and address configuration callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Broadcom Bluetooth support module provides generic functionality
for changing and checking the Bluetooth device address. Use these new
features instead of keeping a duplicate in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This version number is more cosmetic and for debugging purposes, but
since there has been a few changes lately, increase it now.
Two left-over and not used version constants that were never exposed
anywhere are removed since they have no actual value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The init function for each HCI UART protocol prints the same on success
and failure. This information is so generic, remove it and let the main
HCI UART handling print it instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of struct hci_uart_proto should always be const. Change the
function headers and individual protocol drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The TTY layer provides its data pointers as const, but the HCI UART
callbacks expect them as general data pointers. This is of course
wrong and instead of casting them, just fix the individual drivers
to actually take a const data pointer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Casting the tty->disc_data to (void *) is not needed at all. So just
remove this cast and assign the object without a cast.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Broadcom
specific address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Loic Poulain
Peter Hurley
Marcel Holtmann
Frederic Danis
Ben Young Tae Kim
Prasanna Karthik
Ilya Faenson