Mainly for use in debugging and benchmarking, this file allows the user
to control the max frequency used by the GPU. Frequency may still vary
based on workload (if the frequency is set to higher than the minimum)
but won't go over the newly set value.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
They use the same register interfaces, so we can simply enable the
existing code on IVB.
v2:
- resolve conflict with ring freq scaling, we can enable it too
v3:
- resolve conflict again, this time on drm-intel-next
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ring frequency scaling table tells the PCU to treat certain GPU
frequencies as if they were a given CPU frequency for purposes of
scaling the ring frequency. Normally the PCU will scale the ring
frequency based on the CPU P-state, but with the table present, it will
also take the GPU frequency into account.
The main downside of keeping the ring frequency high while the CPU is
at a low frequency (or asleep altogether) is increased power
consumption. But then if you're keeping your GPU busy, you probably
want the extra performance.
v2:
- add units to debug table header (from Eric)
- use tsc_khz as a fallback if the cpufreq driver doesn't give us a freq
(from Chris)
v3:
- fix comments & debug output
- remove unneeded force wake get/put
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Forcewake needs to register itself with drm to use the remove function.
The file also should be read only.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
forcewake is controlled by the open and close of the debugfs file. This
assures that buggy applications cannot cause the GT to stay on forever.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Found by the new strict checking for the mutex being held whilst
manipulating the forcewake status.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a reference count to track the forcewake state of the GPU and
give a safe mechanism for userspace to wake the GT. This also potentially
saves a UC read if the GT is known to be awake already.
The reference count is atomic, but the register access and hardware wake
sequence is protected by struct_mutex.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... to clarify just how we use it inside the driver and remove the
confusion of the poorly matching agp_type names. We still need to
translate through agp_type for interface into the fake AGP driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Currently this is only useful for the rc6 stuff. But this would also be
useful when I finally get around to the logical context + ppgtt stuff.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Fix up the debug file to report the right frequencies. On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side. But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These make us increase our frequency much more readily, and decrease
them only after significant idle time, resulting in a 20% performance
increase for nexuiz.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keith Packard
Jesse Barnes
Ben Widawsky
Daniel Vetter
Chris Wilson