* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Work around a silicon bug in the ac97 reset functionality of the
mpc5200(b). The implementation of the ac97 "cold" reset is flawed.
If the sync and output lines are high when reset is asserted the
attached ac97 device may go into test mode. Avoid this by
reconfiguring the psc to gpio mode and generating the reset manually.
From MPC5200B User's Manual:
"Some AC97 devices goes to a test mode, if the Sync line is high
during the Res line is low (reset phase). To avoid this behavior the
Sync line must be also forced to zero during the reset phase. To do
that, the pin muxing should switch to GPIO mode and the GPIO control
register should be used to control the output lines."
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: Do not suspend IPI IRQs.
powerpc: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupts
ixp4xx-beeper: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupt
irq: Add new IRQ flag IRQF_NO_SUSPEND
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (79 commits)
powerpc/8xx: Add support for the MPC8xx based boards from TQC
powerpc/85xx: Introduce support for the Freescale P1022DS reference board
powerpc/85xx: Adding DTS for the STx GP3-SSA MPC8555 board
powerpc/85xx: Change deprecated binding for 85xx-based boards
powerpc/tqm85xx: add a quirk for ti1520 PCMCIA bridge
powerpc/tqm85xx: update PCI interrupt-map attribute
powerpc/mpc8308rdb: support for MPC8308RDB board from Freescale
powerpc/fsl_pci: add quirk for mpc8308 pcie bridge
powerpc/85xx: Cleanup QE initialization for MPC85xxMDS boards
powerpc/85xx: Fix booting for P1021MDS boards
powerpc/85xx: Fix SWIOTLB initalization for MPC85xxMDS boards
powerpc/85xx: kexec for SMP 85xx BookE systems
powerpc/5200/i2c: improve i2c bus error recovery
of/xilinxfb: update tft compatible versions
powerpc/fsl-diu-fb: Support setting display mode using EDID
powerpc/5121: doc/dts-bindings: update doc of FSL DIU bindings
powerpc/5121: shared DIU framebuffer support
powerpc/5121: move fsl-diu-fb.h to include/linux
powerpc/5121: fsl-diu-fb: fix issue with re-enabling DIU area descriptor
powerpc/512x: add clock structure for Video-IN (VIU) unit
...
Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board. This patch excludes the DIU, SSI, and MMC/SD
drivers. Only a 36-bit DTS is provided.
Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default ti1520 bridge expects an input clock on CLOCK pin (to control
power chip). However on this boards CLOCK should be generated by PCI1520
itself. Add a quirk that enables internal 16 KHz clock generation on
this pin.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for MPC8308RDB development board from
Freescale.
Supported devices:
DUART
Dual Ethernet
NOR and NAND flashes
I2C
USB in peripheral mode
PCIE support is broken by the commit 3da34aa ("powerpc/fsl: Support
unique MSI addresses per PCIe Root Complex"). Works after revert.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_mds_setup_arch() function is incomprehensible
and unmaintainable. Factor out all QE specific stuff into
mpc85xx_mds_qe_init() and mpc85xx_mds_reset_ucc_phys().
Also move QE stuff out of mpc85xx_mds_pic_init().
The diff is unreadable, but only because the code was so. ;-)
It should be better now, and less indented.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.
This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code inside '#ifdef CONFIG_QUICC_ENGINE' makes the
mpc85xx_mds_setup_arch() return early if no QE nodes present,
and so SWIOTLB is never initialized.
This patch fixes the issue by moving SWIOTLB code above
QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for kexec on 85xx machines for the BookE platform.
Including support for SMP machines
Based off work from Maxim Uvarov <muvarov@mvista.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow board selection in a drop-down board sub-menu
like many other platforms do.
Before the patch:
...
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
Patched:
...
[*] 512x-based boards
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
This is a cleanup before adding new board selection entry.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves the declaration of of_get_address(), of_get_pci_address(),
and of_pci_address_to_resource() out of arch code and into the common
linux/of_address header file.
This patch also fixes some of the asm/prom.h ordering issues. It still
includes some header files that it ideally shouldn't be, but at least the
ordering is consistent now so that of_* overrides work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If a CPU remove is attempted using the 'release' interface on hardware
which supports extended cede, the CPU will be put in the INACTIVE state
rather than the OFFLINE state due to the default preferred_offline_state
in that situation. In the INACTIVE state it will fail to be removed.
This patch changes the preferred offline state to OFFLINE when an CPU is
in the ONLINE state. After cpu_down() is called in dlpar_offline_cpu()
the CPU will be OFFLINE and CPU removal can continue.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for the Mac Mini's that were quietly rolled out
in 2005. Work still needs to be done to support suspend and
WakeOnLan.
Signed-off-by: Mark Crichton <crichton@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds
Al Viro
Christoph Hellwig
Eric Millbrandt
Benjamin Herrenschmidt
Heiko Schocher
Timur Tabi
Dmitry Eremin-Solenikov
Ilya Yanok
Anton Vorontsov
Jiri Kosina
Matthew McClintock
Anatolij Gustschin
Grant Likely
Robert Jennings