While load balancing, if all tasks on the source runqueue are pinned,
we retry after excluding the corresponding source cpu. However, loop counters
env.loop and env.loop_break are not reset before retrying, which can lead
to failure in moving the tasks. In this patch we reset env.loop and
env.loop_break to their inital values before we retry.
Signed-off-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FE06EEF.2090709@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Traversing an entire package is not only expensive, it also leads to tasks
bouncing all over a partially idle and possible quite large package. Fix
that up by assigning a 'buddy' CPU to try to motivate. Each buddy may try
to motivate that one other CPU, if it's busy, tough, it may then try its
SMT sibling, but that's all this optimization is allowed to cost.
Sibling cache buddies are cross-wired to prevent bouncing.
4 socket 40 core + SMT Westmere box, single 30 sec tbench runs, higher is better:
clients 1 2 4 8 16 32 64 128
..........................................................................
pre 30 41 118 645 3769 6214 12233 14312
post 299 603 1211 2418 4697 6847 11606 14557
A nice increase in performance.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1339471112.7352.32.camel@marge.simpson.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the event of CPU hotplug, the kernel modifies the cpusets' cpus_allowed
masks as and when necessary to ensure that the tasks belonging to the cpusets
have some place (online CPUs) to run on. And regular CPU hotplug is
destructive in the sense that the kernel doesn't remember the original cpuset
configurations set by the user, across hotplug operations.
However, suspend/resume (which uses CPU hotplug) is a special case in which
the kernel has the responsibility to restore the system (during resume), to
exactly the same state it was in before suspend.
In order to achieve that, do the following:
1. Don't modify cpusets during suspend/resume. At all.
In particular, don't move the tasks from one cpuset to another, and
don't modify any cpuset's cpus_allowed mask. So, simply ignore cpusets
during the CPU hotplug operations that are carried out in the
suspend/resume path.
2. However, cpusets and sched domains are related. We just want to avoid
altering cpusets alone. So, to keep the sched domains updated, build
a single sched domain (containing all active cpus) during each of the
CPU hotplug operations carried out in s/r path, effectively ignoring
the cpusets' cpus_allowed masks.
(Since userspace is frozen while doing all this, it will go unnoticed.)
3. During the last CPU online operation during resume, build the sched
domains by looking up the (unaltered) cpusets' cpus_allowed masks.
That will bring back the system to the same original state as it was in
before suspend.
Ultimately, this will not only solve the cpuset problem related to suspend
resume (ie., restores the cpusets to exactly what it was before suspend, by
not touching it at all) but also speeds up suspend/resume because we avoid
running cpuset update code for every CPU being offlined/onlined.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120524141611.3692.20155.stgit@srivatsabhat.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU, perf, and scheduler fixes from Ingo Molnar.
The RCU fix is a revert for an optimization that could cause deadlocks.
One of the scheduler commits (164c33c6ad "sched: Fix fork() error path
to not crash") is correct but not complete (some architectures like Tile
are not covered yet) - the resulting additional fixes are still WIP and
Ingo did not want to delay these pending fixes. See this thread on
lkml:
[PATCH] fork: fix error handling in dup_task()
The perf fixes are just trivial oneliners.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "rcu: Move PREEMPT_RCU preemption to switch_to() invocation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix segfault with report and mixed guestmount use
perf kvm: Fix regression with guest machine creation
perf script: Fix format regression due to libtraceevent merge
ring-buffer: Fix accounting of entries when removing pages
ring-buffer: Fix crash due to uninitialized new_pages list head
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS/sched: Update scheduler file pattern
sched/nohz: Rewrite and fix load-avg computation -- again
sched: Fix fork() error path to not crash
Thanks to Charles Wang for spotting the defects in the current code:
- If we go idle during the sample window -- after sampling, we get a
negative bias because we can negate our own sample.
- If we wake up during the sample window we get a positive bias
because we push the sample to a known active period.
So rewrite the entire nohz load-avg muck once again, now adding
copious documentation to the code.
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Reported-and-tested-by: Charles Wang <muming.wq@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1340373782.18025.74.camel@twins
[ minor edits ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 616c310e83.
(Move PREEMPT_RCU preemption to switch_to() invocation).
Testing by Sasha Levin <levinsasha928@gmail.com> showed that this
can result in deadlock due to invoking the scheduler when one of
the runqueue locks is held. Because this commit was simply a
performance optimization, revert it.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Fix lots of new kernel-doc warnings in kernel/sched/fair.c:
Warning(kernel/sched/fair.c:3625): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3625): Excess function parameter 'sd' description in 'update_sg_lb_stats'
Warning(kernel/sched/fair.c:3735): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'sd' description in 'update_sd_pick_busiest'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'this_cpu' description in 'update_sd_pick_busiest'
.. more warnings
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It does not get processed because sched_domain_level_max is 0 at the
time that setup_relax_domain_level() is run.
Simply accept the value as it is, as we don't know the value of
sched_domain_level_max until sched domain construction is completed.
Fix sched_relax_domain_level in cpuset. The build_sched_domain() routine calls
the set_domain_attribute() routine prior to setting the sd->level, however,
the set_domain_attribute() routine relies on the sd->level to decide whether
idle load balancing will be off/on.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120605184436.GA15668@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Often when we run into mis-shapen topologies the balance iteration
fails to update the cpu power properly and we'll end up in /0 traps.
Always initialize the cpu-power to a semi-sane value so that we can
at least boot the machine, even if the load-balancer might not
function correctly.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3lbhyj25sr169ha7z3qht5na@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Weird topologies can lead to asymmetric domain setups. This needs
further consideration since these setups are typically non-minimal
too.
For now, make it work by adding an extra mask selecting which CPUs
are allowed to iterate up.
The topology that triggered it is the one from David Rientjes:
10 20 20 30
20 10 20 20
20 20 10 20
30 20 20 10
resulting in boxes that wouldn't even boot.
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3p86l9cuaqnxz7uxsojmz5rm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Roland Dreier reported spurious, hard to trigger lockdep warnings
within the scheduler - without any real lockup.
This bit gives us the right clue:
> [89945.640512] [<ffffffff8103fa1a>] double_lock_balance+0x5a/0x90
> [89945.640568] [<ffffffff8104c546>] push_rt_task+0xc6/0x290
if you look at that code you'll find the double_lock_balance() in
question is the one in find_lock_lowest_rq() [yay for inlining].
Now find_lock_lowest_rq() has a bug.. it fails to use
double_unlock_balance() in one exit path, if this results in a retry in
push_rt_task() we'll call double_lock_balance() again, at which point
we'll run into said lockdep confusion.
Reported-by: Roland Dreier <roland@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337282386.4281.77.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit cb83b629b ("sched/numa: Rewrite the CONFIG_NUMA sched
domain support") removed the NODE sched domain and started checking
if the node distance in SLIT table is farther than REMOTE_DISTANCE,
if so, it will lose the load balance chance at exec/fork/wake_affine
points.
But actually, even the node distance is farther than REMOTE_DISTANCE.
Modern CPUs also has QPI like connections, which ensures that memory
access is not too slow between nodes. So the above change in behavior
on NUMA machine causes a performance regression on various benchmarks:
hackbench, tbench, netperf, oltp, etc.
This patch will recover the scheduler behavior to old mode on all my
Intel platforms: NHM EP/EX, WSM EP, SNB EP/EP4S, and thus fixes the
perfromance regressions. (all of them just have 2 kinds distance, 10, 21)
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338965571-9812-1-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
task_tick_rt() has an optimization to only reschedule SCHED_RR tasks
if they were the only element on their rq. However, with cgroups
a SCHED_RR task could be the only element on its per-cgroup rq but
still be competing with other SCHED_RR tasks in its parent's
cgroup. In this case, the SCHED_RR task in the child cgroup would
never yield at the end of its timeslice. If the child cgroup
rt_runtime_us was the same as the parent cgroup rt_runtime_us,
the task in the parent cgroup would starve completely.
Modify task_tick_rt() to check that the task is the only task on its
rq, and that the each of the scheduling entities of its ancestors
is also the only entity on its rq.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337229266-15798-1-git-send-email-ccross@android.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
SD_OVERLAP exists to allow overlapping groups, overlapping groups
appear in NUMA topologies that aren't fully connected.
The typical result of not fully connected NUMA is that each cpu (or
rather node) will have different spans for a particular distance.
However due to how sched domains are traversed -- only the first cpu
in the mask goes one level up -- the next level only cares about the
spans of the cpus that went up.
Due to this two things were observed to be broken:
- build_overlap_sched_groups() -- since its possible the cpu we're
building the groups for exists in multiple (or all) groups, the
selection criteria of the first group didn't ensure there was a cpu
for which is was true that cpumask_first(span) == cpu. Thus load-
balancing would terminate.
- update_group_power() -- assumed that the cpu span of the first
group of the domain was covered by all groups of the child domain.
The above explains why this isn't true, so deal with it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1337788843.9783.14.camel@laptop
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Follow up on commit 556061b00 ("sched/nohz: Fix rq->cpu_load[]
calculations") since while that fixed the busy case it regressed the
mostly idle case.
Add a callback from the nohz exit to also age the rq->cpu_load[]
array. This closes the hole where either there was no nohz load
balance pass during the nohz, or there was a 'significant' amount of
idle time between the last nohz balance and the nohz exit.
So we'll update unconditionally from the tick to not insert any
accidental 0 load periods while busy, and we try and catch up from
nohz idle balance and nohz exit. Both these are still prone to missing
a jiffy, but that has always been the case.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: pjt@google.com
Cc: Venkatesh Pallipadi <venki@google.com>
Link: http://lkml.kernel.org/n/tip-kt0trz0apodbf84ucjfdbr1a@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Prashanth Nageshappa
Mike Galbraith
Srivatsa S. Bhat
Linus Torvalds
Peter Zijlstra
Paul E. McKenney
Randy Dunlap
Dimitri Sivanich
Alex Shi
Kamalesh Babulal
Hiroshi Shimamoto
Colin Cross
Peter Zijlstra