Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver. This driver
implements support for this within the standard LED class.
Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver. The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.
This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Driver for PC Engines ALIX.2 and ALIX.3 LEDs.
Signed-off-by: Constantin Baranov <const@mimas.ru>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
HP notebooks contain accelerometer-based disk protection subsystem,
and LED that indicates hard disk is protected. This is driver for the
LED part.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The cm-x270 board uses leds-gpio so remove the now unneeded driver.
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This allows LEDs to be controlled as a backlight device where
they turn off and on when the display is blanked and unblanked.
This is useful where you need various key backlight LEDs to
dim at the same time as the backlight.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz
Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi
Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NXP pca9532 is a LED dimmer/controller attached to i2c bus. It allows
attaching upto 16 leds which can either be on, off or dimmed and/or blinked
with the two PWM modulators available.
This driver is a "new-style" i2c driver that adheres to the driver model and
implements the led framework api. Since the leds connected to the driver are
platform specific, it is only useful when platform data is passed to the
driver to define what leds are connected to which pins.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Add a trigger which allows LEDs to default to the full
brightness state.
Signed-off-by: Nick Forbes <Nick.Forbes@huntsworth.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The LEDs on the Freecom FSG-3 are connected to an external
memory-mapped latch on the ixp4xx expansion bus, and therefore cannot
be supported by any of the existing LEDs drivers.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This is a LED driver using the PWM on newer SOCs from Atmel; brightness is
controlled by changing the PWM duty cycle. So for example if you've set up
two leds labeled "pwm0" and "pwm1":
echo 0 > /sys/class/leds/pwm2/brightness # off (0%)
echo 80 > /sys/class/leds/pwm2/brightness
echo 255 > /sys/class/leds/pwm2/brightness # on (100%)
Note that "brightness" here isn't linear; maybe that should change. Going
from 4 to 8 probably doubles perceived brightness, while 244 to 248 is
imperceptible.
This is mostly intended to be a simple example of PWM, although it's
realistic since LCD backlights are often driven with PWM to conserve
battery power (and offer brightness options).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the LEDs on the HP Jornada 620/660/680/690 devices.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
All boards using the IXP4XX-GPIO-LED driver have been updated to use
the generic leds-gpio driver instead.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The driver supports the mail LED commonly found on different Clevo notebooks.
The driver access the LED through the i8042 hardware which is handled by
the input subsystem.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The leds-cobalt driver only supports the Coable Qube series
(not included in Cobalt Raq series).
Rename the driver and update Kconfig/Makefile.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This patch adds support for GPIO connected leds via the new GPIO framework.
Information about leds (gpio, polarity, name, default trigger) is passed
to the driver via platform_data.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Eric Piel
Mark Brown
Constantin Baranov
Pavel Machek
Richard Purdie
Rodolfo Giometti
Mike Rapoport
David S. Miller
Eric Miao
Nate Case
Riku Voipio
Nick Forbes
Rod Whitby
Dmitry Baryshkov
David Brownell
Kristoffer Ericson
Márton Németh
Yoichi Yuasa
Raphael Assenat
Florian Fainelli