This avoids a WARNING splat when loading the macsonic or macmace driver.
Please see commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask").
This implementation of arch_setup_pdev_archdata() differs from the
powerpc one, in that this one avoids clobbering a device dma mask
which has already been initialized.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Revive support for 64-bit get_user(), which was disabled in commit
d94af931af ("[PATCH] m68k: clean up uaccess.h") due to a "broken"
typeof in (then brand new) gcc-4.1.
- Keep on using u64 for the temporary, as __typeof__() doesn't drop
the const qualifier,
- Move it into a union (like mips32 does) to get rid of the cast, as
using get_user() to fetch a __user pointer would cause a "cast to
pointer from integer of different size" warning otherwise.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Martijn Coenen <maco@android.com>
ndelay() is supposed to take an unsigned long, but if you define
ndelay() as a macro and the caller pass an unsigned long long instead
of an unsigned long, the unsigned long long to unsigned long cast is
not done and we end up with an "undefined reference to `__udivdi3'"
error at link time.
Fix that by making ndelay() an inline function and then defining dummy
ndelay() macro that redirects to the ndelay() function (it's how most
archs do to implement ndelay()).
Fixes: c8ee038bd1 ("m68k: Implement ndelay() based on the existing udelay() logic")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
[geert: Remove comment now it is no longer a macro]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
We have two ways of getting the current time from a platform at boot
or during suspend: either using read_persistent_clock() or the rtc
class operation. We never need both, so I'm hiding the
read_persistent_clock variant when the generic RTC is enabled.
Since read_persistent_clock() and mktime() are deprecated because of
the y2038 overflow of time_t, we should use the time64_t based
replacements here.
Finally, the dependency on CONFIG_ARCH_USES_GETTIMEOFFSET looks
completely bogus in this case, so let's remove that. It was
added in commit b13b3f51ff ("m68k: fix inclusion of
arch_gettimeoffset for non-MMU 68k classic CPU types") to deal
with arch_gettimeoffset(), which has since been removed from
this file and is unrelated to the RTC functions.
The rtc accessors are only used by classic machines, while
coldfire uses proper RTC drivers, so we can put the old
ifdef back around both functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This fixes a bug in read_persistent_clock() which causes the system
clock to lag the Real Time Clock by one month. The problem was noticed
on a Mac, but theoretically it must also affect Atari, BVME6000 and Q40.
The tm_mon value in the struct rtc_time passed to mach_hwclk() is
zero-based, and atari_mste_hwclk(), atari_tt_hwclk(), bvme6000_hwclk(),
mac_hwclk() and q40_hwclk() all make this adjustment. Unfortunately,
dn_dummy_hwclk(), mvme147_hwclk(), mvme16x_hwclk(), sun3_hwclk() and
sun3x_hwclk() fail to decrement tm_mon. Also m68328_hwclk() assumes
a one-based tm_mon.
Bring these platforms into line and fix read_persistent_clock() so it
works correctly on all m68k platforms.
The datasheets for the RTC devices found on the affected platforms
all confirm that the year is stored as a value in the range 0-99 and
the month is stored as a value in the range 1-12. Please refer to the
datasheets for MC146818 (Apollo), DS1643 (MVME), ICM7170 (Sun 3)
and M48T02 (Sun 3x).
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Pull m68knommu update from Greg Ungerer:
"Only a single fix to set the DMA masks in the ColdFire FEC platform
data structure.
This stops the warning from dma-mapping.h at boot time"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: set dma and coherent masks for platform FEC ethernets
Pull siginfo updates from Eric Biederman:
"The work on cleaning up and getting the bugs out of siginfo generation
was largely stalled this round. The progress that was made was the
definition of FPE_FLTUNK. Which is usable to fix many of the cases
where siginfo generation is erroneously generating SI_USER by setting
si_code to 0, that has recently been tagged as FPE_FIXME.
You already have the change by way of the arm64 tree as that
definition was pulled into the arm64 tree to allow fixing the problem
there.
What remains is the second round of fixing for what I thought was a
trivial change to the struct siginfo when put the union in _sigfault
where it belongs. Do to historical reasons 32bit m68k only ensures
that pointers are 2 byte aligned. So I have added a m68k test case
made of BUILD_BUG_ONs to verify I have this fix correct and possibly
catch problems, and I have computed the number of bytes of padding
needed for the _addr_bnd and _addr_pkey cases and just use an array of
characters that size.
For pure paranoia I have written the code so if there is an
architecture out there that does not perform any alignment of
structures it should still work.
With the removal of all of the stale arechitectures this cycle future
work on cleaning up struct siginfo should be much easier. Almost all
of the conflicting si_code definitions have been removed with the
removal of (blackfin, tile, and frv). Plus some of the most difficult
to test cases have simply been removed from the tree.
Which means that with a little luck copy_siginfo_to_user can become a
light weight wrapper around copy_to_user in the next cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
m68k: Verify the offsets in struct siginfo never change.
signal: Correct the offset of si_pkey and si_lower in struct siginfo on m68k
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
Pull removal of in-kernel calls to syscalls from Dominik Brodowski:
"System calls are interaction points between userspace and the kernel.
Therefore, system call functions such as sys_xyzzy() or
compat_sys_xyzzy() should only be called from userspace via the
syscall table, but not from elsewhere in the kernel.
At least on 64-bit x86, it will likely be a hard requirement from
v4.17 onwards to not call system call functions in the kernel: It is
better to use use a different calling convention for system calls
there, where struct pt_regs is decoded on-the-fly in a syscall wrapper
which then hands processing over to the actual syscall function. This
means that only those parameters which are actually needed for a
specific syscall are passed on during syscall entry, instead of
filling in six CPU registers with random user space content all the
time (which may cause serious trouble down the call chain). Those
x86-specific patches will be pushed through the x86 tree in the near
future.
Moreover, rules on how data may be accessed may differ between kernel
data and user data. This is another reason why calling sys_xyzzy() is
generally a bad idea, and -- at most -- acceptable in arch-specific
code.
This patchset removes all in-kernel calls to syscall functions in the
kernel with the exception of arch/. On top of this, it cleans up the
three places where many syscalls are referenced or prototyped, namely
kernel/sys_ni.c, include/linux/syscalls.h and include/linux/compat.h"
* 'syscalls-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: (109 commits)
bpf: whitelist all syscalls for error injection
kernel/sys_ni: remove {sys_,sys_compat} from cond_syscall definitions
kernel/sys_ni: sort cond_syscall() entries
syscalls/x86: auto-create compat_sys_*() prototypes
syscalls: sort syscall prototypes in include/linux/compat.h
net: remove compat_sys_*() prototypes from net/compat.h
syscalls: sort syscall prototypes in include/linux/syscalls.h
kexec: move sys_kexec_load() prototype to syscalls.h
x86/sigreturn: use SYSCALL_DEFINE0
x86: fix sys_sigreturn() return type to be long, not unsigned long
x86/ioport: add ksys_ioperm() helper; remove in-kernel calls to sys_ioperm()
mm: add ksys_readahead() helper; remove in-kernel calls to sys_readahead()
mm: add ksys_mmap_pgoff() helper; remove in-kernel calls to sys_mmap_pgoff()
mm: add ksys_fadvise64_64() helper; remove in-kernel call to sys_fadvise64_64()
fs: add ksys_fallocate() wrapper; remove in-kernel calls to sys_fallocate()
fs: add ksys_p{read,write}64() helpers; remove in-kernel calls to syscalls
fs: add ksys_truncate() wrapper; remove in-kernel calls to sys_truncate()
fs: add ksys_sync_file_range helper(); remove in-kernel calls to syscall
kernel: add ksys_setsid() helper; remove in-kernel call to sys_setsid()
kernel: add ksys_unshare() helper; remove in-kernel calls to sys_unshare()
...
A change to the generic struct siginfo accidentally changed the offset
of si_offset. Add build time checks to ensure the offsets of all known
fields in struct siginfo never change. This copies the form of similar
changes on x86.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Using this helper allows us to avoid the in-kernel calls to the
sys_mmap_pgoff() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_mmap_pgoff().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As of commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask") the Freescale FEC driver is issuing the following
warning on driver initialization on ColdFire systems:
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 0x40159e20
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc7-dirty #4
Stack from 41833dd8:
41833dd8 40259c53 40025534 40279e26 00000003 00000000 4004e514 41827000
400255de 40244e42 00000204 40159e20 00000009 00000000 00000000 4024531d
40159e20 40244e42 00000204 00000000 00000000 00000000 00000007 00000000
00000000 40279e26 4028d040 40226576 4003ae88 40279e26 418273f6 41833ef8
7fffffff 418273f2 41867028 4003c9a2 4180ac6c 00000004 41833f8c 4013e71c
40279e1c 40279e26 40226c16 4013ced2 40279e26 40279e58 4028d040 00000000
Call Trace:
[<40025534>] 0x40025534
[<4004e514>] 0x4004e514
[<400255de>] 0x400255de
[<40159e20>] 0x40159e20
[<40159e20>] 0x40159e20
It is not fatal, the driver and the system continue to function normally.
As per the warning the coherent_dma_mask is not set on this device.
There is nothing special about the DMA memory coherency on this hardware
so we can just set the mask to 32bits in the platform data for the FEC
ethernet devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
According to Apple's Developer Notes, all of the early PowerBook models
have their RTC connected to VIA1. Use the VIA clock ops as appropriate.
This was tested on a PowerBook 170.
Don't use the VIA ops when not appropriate. Calling unimplemented clock
or PRAM getter or setter ops can now result in an error instead of
failing silently.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The PMU watchdog will power down the system if the kernel is slow
to start up, e.g. due to unpacking a large initrd. The powerpc
version of this driver (via-pmu.c) has a solution for the same
problem. It uses this call sequence:
setup_arch
find_via_pmu
init_pmu
...
arch_initcall
via_pmu_start
Bring via-pmu68k.c into line with via-pmu.c to fix this issue.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The algorithm used in baboon_irq() appears to be subject to a race
condition: an IRQ flag could be lost if asserted between the MOV
instructions from and to the interrupt flag register. However,
testing shows that the write to the flag register has no effect.
Rewrite this loop to remove the apparent race condition.
No-one seems to know how to clear Baboon IRQ flags, or whether
that's even possible, so add a comment about this.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Stan's tests showed that PDMA improves sequential read performance by
a factor of 5 on a PowerBook 190. Last time I tried this on a
PowerBook 520 it didn't work, so let's not enable it there until
it can be tested with the present mac_scsi driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Finn Thain
Michael Schmitz
Geert Uytterhoeven
Boris Brezillon
Arnd Bergmann
Linus Torvalds
Eric W. Biederman
Dominik Brodowski
Greg Ungerer
Alexandre Belloni