The host_port field is constantly assigned to 0 and this value has
never changed (since time when cpsw driver was introduced. More over,
if this field will be assigned to non 0 value it will break current
driver functionality.
Hence, there are no reasons to continue maintaining this host_port
field and it can be removed, and the HOST_PORT_NUM and ALE_PORT_HOST
defines can be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE APIs expect to receive port masks as input values for arguments
port_mask, untag, reg_mcast, unreg_mcast. But there are few places in
code where port masks are passed left-shifted by cpsw_priv->host_port,
like below:
cpsw_ale_add_vlan(priv->ale, priv->data.default_vlan,
ALE_ALL_PORTS << priv->host_port,
ALE_ALL_PORTS << priv->host_port, 0, 0);
and cpsw is still working just because priv->host_port == 0
and has never ever been changed.
Hence, fix port_mask parameters in ALE APIs calls and drop
"<< priv->host_port" from all places where it's used to
shift valid port mask.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
While building keystone_defconfig of arm we are getting build failure
with the error:
drivers/net/ethernet/ti/netcp_core.c:1846:31: error: invalid type argument of '->' (have 'struct tc_to_netdev')
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
^
drivers/net/ethernet/ti/netcp_core.c:1851:35: error: invalid type argument of '->' (have 'struct tc_to_netdev')
(dev->real_num_tx_queues < tc->tc))
^
drivers/net/ethernet/ti/netcp_core.c:1855:8: error: invalid type argument of '->' (have 'struct tc_to_netdev')
if (tc->tc) {
^
drivers/net/ethernet/ti/netcp_core.c:1856:28: error: invalid type argument of '->' (have 'struct tc_to_netdev')
netdev_set_num_tc(dev, tc->tc);
^
drivers/net/ethernet/ti/netcp_core.c:1857:21: error: invalid type argument of '->' (have 'struct tc_to_netdev')
for (i = 0; i < tc->tc; i++)
^
drivers/net/ethernet/ti/netcp_core.c: At top level:
drivers/net/ethernet/ti/netcp_core.c:1879:2: warning: initialization from incompatible pointer type
.ndo_setup_tc = netcp_setup_tc,
^
The callback of ndo_setup_tc should be:
int (*ndo_setup_tc)(struct net_device *dev, u32 handle, __be16 protocol,
struct tc_to_netdev *tc);
But we missed marking the last argument as a pointer.
Fixes: 16e5cc6471 ("net: rework setup_tc ndo op to consume general tc operand")
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.
Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.
Rename the helpers to match with the updated dma desc field sw_data.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8990777914 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.
The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.
Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].
Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.
Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci_cpdma mixes up physical addresses as seen from the CPU
and DMA addresses as seen from a DMA master, since it can operate
on both normal memory or an on-chip buffer. If dma_addr_t is
different from phys_addr_t, this means we get a compile-time warning
about the type mismatch:
ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
ethernet/ti/davinci_cpdma.c:182:48: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
pool->cpumap = dma_alloc_coherent(dev, size, &pool->phys,
In file included from ethernet/ti/davinci_cpdma.c:21:0:
dma-mapping.h:398:21: note: expected 'dma_addr_t * {aka long long unsigned int *}' but argument is of type 'phys_addr_t * {aka unsigned int *}'
static inline void *dma_alloc_coherent(struct device *dev, size_t size,
This slightly restructures the code so the address we use for
mapping RAM into a DMA address is always a dma_addr_t, avoiding
the warning. The code is correct even if both types are 32-bit
because the DMA master in this device only supports 32-bit addressing
anyway, independent of the types that are used.
We still assign this value to pool->phys, and that is wrong if
the driver is ever used with an IOMMU, but that value appears to
be never used, so there is no problem really. I've added a couple
of comments about where we do things that are slightly violating
the API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the TI cpamc driver. This results in the following error message.
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_probe':
drivers/net/ethernet/ti/cpmac.c:1119:18: error:
'struct mii_bus' has no member named 'phy_map'
Fixes: 7f854420fb ("phy: Add API for {un}registering an mdio device to a bus")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
A cleanup patch I did was unfortunately wrong and introduced
multiple serious bugs in the netcp rx processing, as indicated
by these correct gcc warnings:
drivers/net/ethernet/ti/netcp_core.c:776:14: warning: 'buf_ptr' may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/ti/netcp_core.c:687:14: warning: 'ptr' may be used uninitialized in this function [-Wuninitialized]
I have checked the patch once more and found that a call to
get_pkt_info() accidentally got removed in netcp_free_rx_desc_chain,
and netcp_process_one_rx_packet no longer retrieved the correct
buffer length. This patch should fix all the known problems,
but I did not test on real hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8990777914 ("netcp: try to reduce type confusion in descriptors")
Signed-off-by: David S. Miller <davem@davemloft.net>
When a fixed-link sub-node exists in a slave node, the slave node
is also the PHY node. Since this is a separate use of the slave node,
of_node_get() should be used to increment the reference count.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1f71e8c96f ("drivers: net: cpsw: Add
support for fixed-link PHY") did not parse the "phy-mode" property in
the case of a fixed-link PHY, leaving slave_data->phy_if with its default
of PHY_INTERFACE_MODE_NA(0). This later gets passed to phy_connect() in
cpsw_slave_open(), and eventually to cpsw_phy_sel() where it hits a default
case that configures the MAC for MII mode.
The user visible symptom is that while kernel log messages seem to indicate
that the interface is set up, there is no network communication. Eventually
a watchdog error occurs:
NETDEV WATCHDOG: eth0 (cpsw): transmit queue 0 timed out
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using more than one slave with ti cpsw and fixed phy the pd->phy_id
will be always zero, but slave_data->phy_id must be unique. pd->phy_id
means a "phy hardware id" whereas slave_data->phy_id means an "unique id",
so we should use pd->addr which has the same unique meaning.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: Pascal Speck <kernel@iktek.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.
Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21: expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21: got restricted __le32 *<noident>
This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko
John Fastabend
David S. Miller
Sudip Mukherjee
Karicheri, Muralidharan
David Rivshin
Arnd Bergmann
Guenter Roeck
Andrew Lunn
Julia Lawall
Pascal Speck (Iktek)