Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
Pull x86 mm updates from Ingo Molnar:
"The dominant change in this cycle was the continued work to isolate
kernel drivers from MTRR legacies: this tree gets rid of all kernel
internal driver interfaces to MTRRs (mostly by rewriting it to proper
PAT interfaces), the only access left is the /proc/mtrr ABI.
This work was done by Luis R Rodriguez.
There's also some related PCI interface additions for which I've
Cc:-ed Bjorn"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/mtrr: Remove kernel internal MTRR interfaces: unexport mtrr_add() and mtrr_del()
s390/io: Add pci_iomap_wc() and pci_iomap_wc_range()
drivers/dma/iop-adma: Use dma_alloc_writecombine() kernel-style
drivers/video/fbdev/vt8623fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/s3fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/arkfb.c: Use arch_phys_wc_add() and pci_iomap_wc()
PCI: Add pci_iomap_wc() variants
drivers/video/fbdev/gxt4500: Use pci_ioremap_wc_bar() to map framebuffer
drivers/video/fbdev/kyrofb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
drivers/video/fbdev/i740fb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
PCI: Add pci_ioremap_wc_bar()
x86/mm: Make kernel/check.c explicitly non-modular
x86/mm/pat: Make mm/pageattr[-test].c explicitly non-modular
x86/mm/pat: Add comments to cachemode translation tables
arch/*/io.h: Add ioremap_uc() to all architectures
drivers/video/fbdev/atyfb: Use arch_phys_wc_add() and ioremap_wc()
drivers/video/fbdev/atyfb: Replace MTRR UC hole with strong UC
drivers/video/fbdev/atyfb: Clarify ioremap() base and length used
drivers/video/fbdev/atyfb: Carve out framebuffer length fudging into a helper
x86/mm, asm-generic: Add IOMMU ioremap_uc() variant default
...
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
* pci/host-dra7xx:
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
* pci/host-imx6:
PCI: imx6: Simplify a trivial if-return sequence
* pci/host-spear:
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Previously we checked for invalid MPS settings, i.e., a device with MPS
different than its upstream bridge, in pcie_bus_detect_mps(). We only did
this if the arch or hotplug driver called pcie_bus_configure_settings(),
and then only if PCIe bus tuning was disabled (PCIE_BUS_TUNE_OFF).
Move the MPS checking code to pci_configure_device(), so we do it in the
pci_device_add() path for every device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_parse_phandle() returns a device_node pointer with the refcount
incremented. We should dispose of this reference when we're finished.
Drop the reference acquired by of_parse_phandle().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The pcibios_msi_controller() hook was only implemented by ARM, and it sets
pci_bus->msi now, so it doesn't need this hook anymore.
Remove the unused pcibios_msi_controller() hook.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Make pci-host-generic driver (kernel option PCI_HOST_GENERIC) available on
arm64.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM64 requires setup-irq.o to provide pci_fixup_irqs() implementation. We
are adding this now to support the pci-host-generic host controller, but we
enable it for ARM64 PCI so that other host controllers can use this as
well.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The generic OF-based host controller driver uses pci_common_init_dev(),
which is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: changelog, move pcie_bus_configure_settings() before
pci_bus_add_devices(), combine !PCI_PROBE_ONLY blocks]
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
We should not assume any particular hardware topology. Commit d0751b98df
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Linus Torvalds
Bjorn Helgaas
Guilherme G. Piccoli
Luis R. Rodriguez
Zhang Rui
Keith Busch
Lorenzo Pieralisi
Jayachandran C
Fabio Estevam
Yijing Wang
Jiang Liu