Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.
However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.
Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They may contain encrypted information elements (as AMPE frames do)
but they are not encrypted.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh beacons no longer use all-zeroes BSSID. Beacon frames for MBSS,
infrastructure BSS, or IBSS are differentiated by the Capability
Information field in the Beacon frame. A mesh STA sets the ESS and IBSS
subfields to 0 in transmitted Beacon or Probe Response management
frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Note: This breaks compatibility with previous mesh protocol instances.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4. If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).
The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft. See
section 7.1.3.6.3 in current draft (8.0).
Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats. But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMM IE QoS Info field lower 4 bits: Parameter Set Count
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates IEEE802.11 mesh constants to be consistent with newly
approved values. It modifies some values, as well as adds many new constants
in preparation for updating mesh code to the current 802.11s drafts. ANA
numbers were taken from:
https://mentor.ieee.org/802.11/dcn/09/11-09-0031-12-0000-ana-database-assigned-number-authority.xls
A few notes are in order:
1. This will break backwards compatibility with existing Linux kernels as
over-the-air constants have changed.
2. Some old and obsolete constants have been retained for now as the mesh code
itself hasn't been updated yet to the new 802.11s draft. This was desired to
keep the existing mesh scheme working until it can be updated. Adding the
approved values is the first step in updating the mesh code.
3. Obsolete constants have been clearly marked.
4. All ANA approved 802.11s constants have been added.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.
As a side effect, this gets rid of the long code
block to destroy aggregation safely.
Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_hdrlen() should account account new HT Control field in 802.11
data frame header introduced by IEEE 802.11n standard.
According to 802.11n-2009 HT Control field is present in data frames
when both of following are met:
1. It is QoS data frame.
2. Order bit is set in Frame Control field.
The change might be totally compatible with legacy non-11n aware frames,
because 802.11-2007 standard states that "all QoS STAs set this subfield
to 0".
Signed-off-by: Andriy V. Tkachuk <andrit@ukr.net>
Acked-by : Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The header can be used to create qos nullfunc frames, for example.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Unscheduled Automatic Power-Save Delivery (U-APSD) client support. The
idea is that the data frames from the client trigger AP to send the buffered
frames with ACs which have U-APSD enabled. This decreases latency and makes it
possible to save even more power.
Driver needs to use IEEE80211_HW_UAPSD to enable the feature. The current
implementation assumes that firmware takes care of the wakeup and
hardware needing IEEE80211_HW_PS_NULLFUNC_STACK is not yet supported.
Tested with wl1251 on a Nokia N900 and Cisco Aironet 1231G AP and running
various test traffic with ping.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware, for example wl1251 and wl1271, handle the transmission
of power save related frames in hardware, but the driver is responsible
for creating the templates. It's better to create the templates in mac80211,
that way all drivers can benefit from this.
Add two new functions, ieee80211_pspoll_get() and ieee80211_nullfunc_get()
which drivers need to call to get the frame. Drivers are also responsible
for updating the templates after each association.
Also new struct ieee80211_hdr_3addr is added to ieee80211.h to make it
easy to calculate length of the Nullfunc frame.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we insert all user-specified IEs before the HT
IE for association, and after the HT IE for probe requests.
For association, that's correct only if the user-specified
IEs are RSN only, incorrect in all other cases including
WPA. Change this to split apart the user-specified IEs in
two places for association: before the HT IE (e.g. RSN),
after the HT IE (generally empty right now I think?) and
after WMM (all other vendor-specific IEs). For probes,
split the IEs in different places to be correct according
to the spec.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE-802.11n spec says the RX highest data rate field does
not specify the highest supported RX data rate if its not set.
Ignore it if not set then. Refer to section 7.3.56.4
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo
Johannes Berg
Eliad Peller
Thomas Pedersen
Javier Cardona
Bing Zhao
Amitkumar Karwar
Steve deRosier
Felix Fietkau
Johannes Berg
Andriy Tkachuk
Kalle Valo
John W. Linville
Luis R. Rodriguez