Pull UBI/UBIFS updates from Richard Weinberger:
- new config option CONFIG_UBIFS_FS_SECURITY
- minor improvements
- random fixes
* tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs:
ubi: Add debugfs file for tracking PEB state
ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl
ubifs: Remove unnecessary assignment
ubifs: Fix cut and paste error on sb type comparisons
ubi: fastmap: Fix slab corruption
ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels
ubi: Make mtd parameter readable
ubi: Fix section mismatch
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
Add a file under debugfs to allow easy access to the erase count for
each physical erase block on an UBI device. This is useful when
debugging data integrity issues with UBIFS on NAND flash devices.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
v2:
* If ubi_io_is_bad eraseblk_count_seq_show just returns the err.
* if ubi->lookuptbl returns null, its no longer treated as an error
instead info for that block is not printeded
* Removed check for UBI_MAX_ERASECOUNTER since it is impossible to hit
* Removed block state from print, if a block is printed then it is good and
if it is not printed, then it is bad.
v3:
* Remove errant ! symbol from if statement checking if erase count is valid.
Signed-off-by: Richard Weinberger <richard@nod.at>
Booting with UBI fastmap and SLUB debugging enabled results in the
following splats. The problem is that ubi_scan_fastmap() moves the
fastmap blocks from the scan_ai (allocated in scan_fast()) to the ai
allocated in ubi_attach(). This results in two problems:
- When the scan_ai is freed, aebs which were allocated from its slab
cache are still in use.
- When the other ai is being destroyed in destroy_ai(), the
arguments to kmem_cache_free() call are incorrect since aebs on its
->fastmap list were allocated with a slab cache from a differnt ai.
Fix this by making a copy of the aebs in ubi_scan_fastmap() instead of
moving them.
=============================================================================
BUG ubi_aeb_slab_cache (Not tainted): Objects remaining in ubi_aeb_slab_cache on __kmem_cache_shutdown()
-----------------------------------------------------------------------------
INFO: Slab 0xbfd2da3c objects=17 used=1 fp=0xb33d7748 flags=0x40000080
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<8026c47c>] (slab_err+0x78/0x88)
[<8026c47c>] (slab_err) from [<802735bc>] (__kmem_cache_shutdown+0x180/0x3e0)
[<802735bc>] (__kmem_cache_shutdown) from [<8024e13c>] (shutdown_cache+0x1c/0x60)
[<8024e13c>] (shutdown_cache) from [<8024ed64>] (kmem_cache_destroy+0x19c/0x20c)
[<8024ed64>] (kmem_cache_destroy) from [<8057cc14>] (destroy_ai+0x1dc/0x1e8)
[<8057cc14>] (destroy_ai) from [<8057f04c>] (ubi_attach+0x3f4/0x450)
[<8057f04c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
INFO: Object 0xb33d7e88 @offset=3720
INFO: Allocated in scan_peb+0x608/0x81c age=72 cpu=1 pid=118
kmem_cache_alloc+0x3b0/0x43c
scan_peb+0x608/0x81c
ubi_attach+0x124/0x450
ubi_attach_mtd_dev+0x60c/0xff8
ctrl_cdev_ioctl+0x110/0x2b8
do_vfs_ioctl+0xac/0xa00
SyS_ioctl+0x3c/0x64
ret_fast_syscall+0x0/0x1c
kmem_cache_destroy ubi_aeb_slab_cache: Slab cache still has objects
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<8024ed80>] (kmem_cache_destroy+0x1b8/0x20c)
[<8024ed80>] (kmem_cache_destroy) from [<8057cc14>] (destroy_ai+0x1dc/0x1e8)
[<8057cc14>] (destroy_ai) from [<8057f04c>] (ubi_attach+0x3f4/0x450)
[<8057f04c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
cache_from_obj: Wrong slab cache. ubi_aeb_slab_cache but object is from ubi_aeb_slab_cache
------------[ cut here ]------------
WARNING: CPU: 1 PID: 118 at mm/slab.h:354 kmem_cache_free+0x39c/0x450
Modules linked in:
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<80120e40>] (__warn+0xf4/0x10c)
[<80120e40>] (__warn) from [<80120f20>] (warn_slowpath_null+0x28/0x30)
[<80120f20>] (warn_slowpath_null) from [<80271fe0>] (kmem_cache_free+0x39c/0x450)
[<80271fe0>] (kmem_cache_free) from [<8057cb88>] (destroy_ai+0x150/0x1e8)
[<8057cb88>] (destroy_ai) from [<8057ef1c>] (ubi_attach+0x2c4/0x450)
[<8057ef1c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
---[ end trace 2bd8396277fd0a0b ]---
=============================================================================
BUG ubi_aeb_slab_cache (Tainted: G B W ): page slab pointer corrupt.
-----------------------------------------------------------------------------
INFO: Allocated in scan_peb+0x608/0x81c age=104 cpu=1 pid=118
kmem_cache_alloc+0x3b0/0x43c
scan_peb+0x608/0x81c
ubi_attach+0x124/0x450
ubi_attach_mtd_dev+0x60c/0xff8
ctrl_cdev_ioctl+0x110/0x2b8
do_vfs_ioctl+0xac/0xa00
SyS_ioctl+0x3c/0x64
ret_fast_syscall+0x0/0x1c
INFO: Slab 0xbfd2da3c objects=17 used=1 fp=0xb33d7748 flags=0x40000081
INFO: Object 0xb33d7e88 @offset=3720 fp=0xb33d7da0
Redzone b33d7e80: cc cc cc cc cc cc cc cc ........
Object b33d7e88: 02 00 00 00 01 00 00 00 00 f0 ff 7f ff ff ff ff ................
Object b33d7e98: 00 00 00 00 00 00 00 00 bd 16 00 00 00 00 00 00 ................
Object b33d7ea8: 00 01 00 00 00 02 00 00 00 00 00 00 00 00 00 00 ................
Redzone b33d7eb8: cc cc cc cc ....
Padding b33d7f60: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B W 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<80271770>] (free_debug_processing+0x320/0x3c4)
[<80271770>] (free_debug_processing) from [<80271ad0>] (__slab_free+0x2bc/0x430)
[<80271ad0>] (__slab_free) from [<80272024>] (kmem_cache_free+0x3e0/0x450)
[<80272024>] (kmem_cache_free) from [<8057cb88>] (destroy_ai+0x150/0x1e8)
[<8057cb88>] (destroy_ai) from [<8057ef1c>] (ubi_attach+0x2c4/0x450)
[<8057ef1c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
FIX ubi_aeb_slab_cache: Object at 0xb33d7e88 not freed
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
WARNING: vmlinux.o(.text+0x1f2a80): Section mismatch in reference from the variable __param_ops_mtd to the function .init.text:ubi_mtd_param_parse()
The function __param_ops_mtd() references
the function __init ubi_mtd_param_parse().
This is often because __param_ops_mtd lacks a __init
annotation or the annotation of ubi_mtd_param_parse is wrong.
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull block fixes and updates from Jens Axboe:
"Some fixes and followup features/changes that should go in, in this
merge window. This contains:
- Two fixes for lightnvm from Javier, fixing problems in the new code
merge previously in this merge window.
- A fix from Jan for the backing device changes, fixing an issue in
NFS that causes a failure to mount on certain setups.
- A change from Christoph, cleaning up the blk-mq init and exit
request paths.
- Remove elevator_change(), which is now unused. From Bart.
- A fix for queue operation invocation on a dead queue, from Bart.
- A series fixing up mtip32xx for blk-mq scheduling, removing a
bandaid we previously had in place for this. From me.
- A regression fix for this series, fixing a case where we wait on
workqueue flushing from an invalid (non-blocking) context. From me.
- A fix/optimization from Ming, ensuring that we don't both quiesce
and freeze a queue at the same time.
- A fix from Peter on lock ordering for CPU hotplug. Not a real
problem right now, but will be once the CPU hotplug rework goes in.
- A series from Omar, cleaning up out blk-mq debugfs support, and
adding support for exporting info from schedulers in debugfs as
well. This is really useful in debugging stalls or livelocks. From
Omar"
* 'for-linus' of git://git.kernel.dk/linux-block: (28 commits)
mq-deadline: add debugfs attributes
kyber: add debugfs attributes
blk-mq-debugfs: allow schedulers to register debugfs attributes
blk-mq: untangle debugfs and sysfs
blk-mq: move debugfs declarations to a separate header file
blk-mq: Do not invoke queue operations on a dead queue
blk-mq-debugfs: get rid of a bunch of boilerplate
blk-mq-debugfs: rename hw queue directories from <n> to hctx<n>
blk-mq-debugfs: don't open code strstrip()
blk-mq-debugfs: error on long write to queue "state" file
blk-mq-debugfs: clean up flag definitions
blk-mq-debugfs: separate flags with |
nfs: Fix bdi handling for cloned superblocks
block/mq: Cure cpu hotplug lock inversion
lightnvm: fix bad back free on error path
lightnvm: create cmd before allocating request
blk-mq: don't use sync workqueue flushing from drivers
mtip32xx: convert internal commands to regular block infrastructure
mtip32xx: cleanup internal tag assumptions
block: don't call blk_mq_quiesce_queue() after queue is frozen
...
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
From Cyrille:
"""
This pull request contains the following notable changes:
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
When nor's size larger than 16MByte, nor's address width maybe
set to 3 or 4, and controller should change address width according
to nor's setting.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The quadspi is a specialized communication interface targeting single,
dual or quad SPI Flash memories.
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a comment clarifying that NAND subpage write on keystone works,
but is not being enabled in the interest of backward compatibility.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
commit c9711ec525 ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec525 ("mtd: nand: omap: Clean up device tree support")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We accidentally return 1 on error instead of proper error codes.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers are using DMA engine requiring a specific
buffer alignment. The core provides no guarantee on the nand_buffers
pointers, which forces some drivers to allocate their own buffers
and pass the NAND_OWN_BUFFERS flag.
Rework the nand_buffers allocation logic to allocate each buffer
independently. This should make most NAND controllers/DMA engine
happy, and allow us to get rid of these custom buf allocation in
NAND controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Linus Torvalds
Vlastimil Babka
Ben Shelton
Rabin Vincent
Andy Shevchenko
Alexander Couzens
Dan Carpenter
Christoph Hellwig
Brian Norris
Guochun Mao
Ludovic Barre
Kamal Dasu
Sekhar Nori
Roger Quadros
Christophe Jaillet
Masahiro Yamada