Pull another MMC update from Ulf Hansson:
"Here's a second pull request for MMC for v4.10.
As a matter of fact it's only one change that moves some mmc files
around. I thought it was a good idea to get this into v4.10, as it
gives us a nice and fresh base for v4.11. Summary:
MMC core:
- Move files from the card directory to the core directory to enable
future clean-ups of the generic mmc header files and interfaces"
* tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: Move files to core
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Once upon a time it made sense to keep the mmc block device driver and its
related code, in its own directory called card. Over time, more an more
functions/structures have become shared through generic mmc header files,
between the core and the card directory. In other words, the relationship
between them has become closer.
By sharing functions/structures via generic header files, it becomes easy
for outside users to abuse them. In a way to avoid that from happen, let's
move the files from card directory into the core directory, as it enables
us to move definitions of functions/structures into mmc core specific
header files.
Note, this is only the first step in providing a cleaner mmc interface for
outside users. Following changes will do the actual cleanup, as that is not
part of this change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.
Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.
This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy the tuning loop by moving it to a separate function and making it a
for-loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are only 2 possible block sizes, so simplify 2 if-statements into 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").
A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JEDEC specification indicates CMD13 can be used after a HS200 switch
to check for errors. However in practice some boards experience CRC errors
in the CMD13 response. Consequently, for HS200, CRC errors are not a
reliable way to know the switch failed. If there really is a problem, we
would expect tuning will fail and the result ends up the same. So change
the error condition to ignore CRC errors in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds
Ulf Hansson
Masahiro Yamada
Adrian Hunter
Daniel Drake
Zach Brown
Jaehoon Chung
Joonyoung Shim