Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of strict_strtoul() is not preferred, because strict_strtoul()
is obsolete. Thus, kstrtoul() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is
not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch adds const attributes to AB8500 power and temperature related
read-only data arrays.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Some of the comments in the ab8500 drivers reflect the behaviour
of the original device. As this driver now supports newer devices
then these comments are now redundant. Also some IRQ comments are
incorrect.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Tested-by: Rabin VINCENT <rabin.vincent@stericsson.com>
When battery capacity was going below 1% fg is not supposed
to report 0% unless we've got the LOW_BAT IRQ, no matter
what the FG-algorithm says. This made fg get stuck at 1% if
charger is connected when capacity is 1%.
Signed-off-by: Hakan BERG <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Add support for a power cut feature which allows user to
configure when ab8505 and ab8540 based platforms should shut
down system due to low battery.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As HZ is a full-second, there is little point in rounding it.
Let's save a few cycles by using HZ directly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Doing so provides a greater degree of accuracy when dealing with
time-frames between 1us and 20ms. msleep() is only accurate for
wake-ups greater than 20ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Johan BJORNSTEDT <johan.bjornstedt@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Now that we always pass platform specific battery management data
through platform_data instead of obtaining it via different means
depending the way be boot the system (DT or ATAGs); we need to
re-jiggle the way we acquire it in the driver start-up functions.
Now it is wrong for it to be missing, but we still allow Device
Tree code to fiddle with it once we've confirmed it's there.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Wolfram Sang
Jingoo Han
Hongbo Zhang
lme00437
Marcus Cooper
Lee Jones
Hakan Berg
Martin Bergstrom
Rajkumar Kasirajan
Jonas Aaberg
Paer-Olof Haakansson
pender01
Rickard Andersson
Johan Bjornstedt
Anton Vorontsov
Anton Vorontsov