The iseries_veth driver has a timer which we use to send acks. When the
connection is reset or stopped we need to delete the timer.
Currently we only call del_timer() when resetting a connection, which means
the timer might run again while the connection is being re-setup. As it turns
out that's ok, because the flags the timer consults have been reset.
It's cleaner though to call del_timer_sync() once we've dropped the lock,
although the timer may still run between us dropping the lock and calling
del_timer_sync(), but as above that's ok.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Currently the iseries_veth driver prints the file name and line number in its
error messages. This isn't very useful for most users, so just print
"iseries_veth: message" instead.
- convert uses of veth_printk() to veth_debug()/veth_error()/veth_info()
- make terminology consistent, ie. always refer to LPAR not lpar
- be consistent about printing return codes as %d not %x
- make format strings fit in 80 columns
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change sn2-specific calls into generic functions. Without this change
the uncached allocator will not work on non-sn2 platforms.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Vrabel
Correct the ioread* and iowrite* functions. In particular, add an offset to the cookie in ioport_map so we can map I/O port ranges starting from 0 (0 is for reporting errors).
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Steve Longerbeam
Adds an implementation of unaligned LDRD and STRD fixups.
Also fixes a bug where do_alignment() would misinterpret and
fixup an unaligned LDRD/STRD as LDRH/STRH, causing memory
corruption.
This is the same as Patch #2867/1, but with minor whitespace
and comments changes, plus a check for arch-level >= v5TE
before printing ai_dword count in proc_alignment_read().
Signed-off-by: Steve Longerbeam <stevel@mwwireless.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
timer_dyn_reprogram() fails with an OOPS if the
configuration for CONFIG_NO_IDLE_HZ is enabled, and
the system has no support for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Peter Staubach pointed out that it is not correct to check
current->personality & PER_LINUX32 (this will have false
hits on several other personality values).
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes two warnings in arch/ppc/syslib/m8xx_setup.c
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB generic driver
When a USB error occurs that might indicate that the device has been
unplugged, don't resubmit the URB immediately to prevent flooding the
log with error messages before khubd has us disconnect()ed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add register_sound_special_device() function to allow assignment of
device pointer to a specific OSS device for HAL.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michael Ellerman
Tony Luck
Alan Cox
Martin Hicks
Sascha Hauer
David Vrabel
Catalin Marinas
Steve Longerbeam
Jeff Garzik
Russell King
Ben Dooks
Linus Torvalds
Marcelo Tosatti
Ivan Kokshaysky
Clemens Ladisch
Takashi Iwai
Jaroslav Kysela