The comment incorrectly talked about one little-endian quadlet, while
there are actually two. Furthermore, the endianness of the remaining
headers depends on whatever protocol is used, so don't mention them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
handle_ir_buffer_fill() assumed that a completed descriptor would be
indicated by a non-zero transfer_status (as in most other descriptors).
However, this field is written by the controller as soon as (the end of)
the first packet has been written into the buffer. As a consequence, if
we happen to run into such a descriptor when the interrupt handler is
executed after such a packet has completed, the descriptor would be
taken out of the list of active descriptors as soon as the buffer had
been partially filled, so the event for the buffer being completely
filled would never be sent.
To fix this, handle descriptors only when they have been completely
filled, i.e., when res_count == 0. (This also matches the condition
that is reported by the controller with an interrupt.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
CONFIG_FIREWIRE_OHCI_DEBUG could have been exposed to kernel tweakers
if CONFIG_EXPERT was set. But in hindsight, this stuff is far too
useful to omit it. So get rid of two #else branches that are only
going to bitrot otherwise.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
sbp2_send_management_orb() is called by sbp2_login, sbp2_reconnect, and
sbp2_remove, all which are able to sleep during memory allocations.
Actually, sbp2_send_management_orb() itself is a sleeping function.
Login and remove could allocate with GFP_KERNEL but reconnect needs
GFP_NOIO to ensure progress in low memory situations.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
SCSI sense data in SBP-2/3 is carried in an unusual format that means we
have to un-mangle it on our end before we pass it to the SCSI subsystem.
Currently our un-mangling code doesn't quite follow the SBP-2 standard
in that we always assume Current and never Deferred error types, we
never set the VALID bit, and we mishandle the FILEMARK, EOM and ILI
bits.
This patch fixes the sense un-mangling to correctly handle those and
follow the spec.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The firewire-sbp2 module tries to login to an SBP-2/3 target even when
it is running on the local node, which fails because of the inability to
fetch data from DMA mapped regions using firewire transactions on the
local node. It also doesn't make much sense to have the initiator and
target on the same node, so this patch prevents this behaviour.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changed the comment)
If the target's unit directory contains a Unit_Unique_ID entry, we
should use that as the target's GUID for identification purposes. The
SBP-2 standards document says:
"Although the node unique ID (EUI-64) present in the bus information
block is sufficient to uniquely identify nodes attached to Serial Bus,
it is insufficient to identify a target when a vendor implements a
device with multiple Serial Bus node connections. In this case initiator
software requires information by which a particular target may be
uniquely identified, regardless of the Serial Bus access path used."
[ IEEE T10 P1155D Revision 4, Section 7.6 (page 51) ] and
[ IEEE T10 P1467D Revision 5, Section 7.9 (page 74) ]
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
fw_core_handle_request() is called by the low-level driver in tasklet
context or process context, and fw_core_add/remove_address_handler() is
called by mid- or high-level code in process context. So convert
address_handler_lock accesses from those which disable local IRQs to
ones which just disable local softIRQs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix the following unlikely but possible race:
CPU 1 CPU 2
------------------------------------------------------------------------
AR-request tasklet
lookup handler
unregister handler
free handler->callback_data or handler
call handler->callback
The application which registered the handler has no way to stop nodes
sending new requests to their address range, hence cannot prevent this
race.
Fix it simply by extending the address_handler_lock-protected region
from only around the lookup to around both lookup and call. We only
need to do so in the exclusive region handler; the FCP region handler
already holds the lock around the handler->callback call.
Alas this removes the current ability to execute the callback in
parallel on different CPUs if it was called for different FireWire cards
at the same time. (For a single card, the handler is already
serialized.) If this loss of a rather obscure feature is not tolerable,
a more complex fix would be required: Add a handler reference counter;
wait in fw_core_remove_address_handler() for this conter to become zero.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Target-like applications or peer-to-peer-like applications require the
global address handler registration which we have right now, or a per-
card registration. And node lookup, while it would be nice to have,
would be impossible in the brief time between self-ID-complete event and
completion of firewire-core's topology scanning.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Associate all log messages from firewire-core with the respective card
because some people have more than one card. E.g.
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core: created device fw0: GUID 0814438400000389, S800
firewire_core: phy config: new root=ffc1, gap_count=5
firewire_core: created device fw1: GUID 0814438400000388, S800
firewire_core: created device fw2: GUID 0001d202e06800d1, S800
turns into
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core 0000:04:00.0: created device fw0: GUID 0814438400000389, S800
firewire_core 0000:04:00.0: phy config: new root=ffc1, gap_count=5
firewire_core 0000:05:00.0: created device fw1: GUID 0814438400000388, S800
firewire_core 0000:04:00.0: created device fw2: GUID 0001d202e06800d1, S800
This increases the module size slightly; to keep this in check, turn the
former printk wrapper macros into functions. Their implementation is
largely copied from driver core's dev_printk counterparts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Change the log line prefix from "firewire_net: " to "net firewire0: "
etc. for the case that several RFC 2734 interfaces are being used in the
same machine.
Note, the netdev_printk API is not very useful to firewire-net.
netdev_notice(net, "abc\n") would result in irritating messages like
"firewire_ohci 0000:0a:00.0: firewire0: abc". Nor would a dev_printk on
the fw_unit.device to which firewire-net is being bound be useful,
because there are generally multiple ones of those per interface (from
all RFC 2734 peers on the bus, the local node being only one of them).
In the initialization message of each interface, log the PCI device
name of the card which is parent of the netdevice instead of the GUID
of the peer which was semi-randomly used to establish the netdevice.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On second thought, there is little reason to have driver name differ
from module name. Therefore, change
/sys/bus/firewire/drivers/net
/sys/bus/firewire/devices/fw0.0/driver -> [...]/net
/sys/module/firewire_net/drivers/firewire:net
to
/sys/bus/firewire/drivers/firewire_net
/sys/bus/firewire/devices/fw0.0/driver -> [...]/firewire_net
/sys/module/firewire_net/drivers/firewire:firewire_net
It is redundant but consistent with firewire-sbp2's recently changed
driver name.
I don't see this anywhere used, so it should not matter either way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit eba9ebaaa2 "firewire: sbp2: use dev_printk API" changed
messages from e.g.
firewire_sbp2: fw3.0: logged in to LUN 0000 (0 retries)
to
sbp2 fw3.0: logged in to LUN 0000 (0 retries)
because the driver calls itself as "sbp2" when registering with driver
core and with SCSI core. This is of course confusing, so switch to the
name "firewire_sbp2" for driver core in order to match what lsmod and
/sys/module/ show. So we are back to
firewire_sbp2 fw3.0: logged in to LUN 0000 (0 retries)
in the kernel log.
This also changes
/sys/bus/firewire/drivers/sbp2
/sys/bus/firewire/devices/fw3.0/driver -> [...]/sbp2
/sys/module/firewire_sbp2/drivers/firewire:sbp2
to
/sys/bus/firewire/drivers/firewire_sbp2
/sys/bus/firewire/devices/fw3.0/driver -> [...]/firewire_sbp2
/sys/module/firewire_sbp2/drivers/firewire:firewire_sbp2
but "cat /sys/class/scsi_host/host27/proc_name" stays "sbp2" just in
case that proc_name is used by any userland.
The transport detection in lsscsi is not affected. (Tested with lsscsi
version 0.25.) Udev's /dev/disk/by-id and by-path symlinks are not
affected either.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The PCIe device
FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd FireWire Host Controller
[1180:e832] (prog-if 10 [OHCI])
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Audigy's SB1394 controller is actually from Texas Instruments
and has the same bus reset packet generation bug, so it needs the
same quirk entry.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
fw_unit device drivers invariably need to talk to the fw_unit's parent
(an fw_device) and grandparent (an fw_card). firewire-core already
maintains an fw_card reference for the entire lifetime of an fw_device.
Likewise, let firewire-core maintain an fw_device reference for the
entire lifetime of an fw_unit so that fw_unit drivers don't have to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Ensure that the EXPORT_SYMBOL macros are present for when we clean up
the "module.h" is everywhere situation, to prevent build failures.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add the dma_sync_single_* calls necessary to ensure proper cache
synchronization for isochronous data buffers on non-coherent
architectures.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch
Stefan Richter
Chris Boot
santosh nayak
Rusty Russell
Linus Torvalds
Paul Gortmaker