track sched job status like the length of job queue and hw job queue.
v2: fix build after rebase
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Insert wait for reg mem after EOP to fix potential issue with vm context switch
v2: move wait to vm_flush() use equal instead of greater than.
Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
three nouveau regression fixes.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
Broken since "gr: convert user classes to new-style nvkm_object"
Tested on a PPC64 G5 + NV34
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
bunch of drm fixes.
* tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel:
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Fixes headed for v4.3-rc1, including Maarten's DP MST state checker fix
you requested.
* tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just like single link MIPI panels, similarly for dual link panels, pipe
to be configured is based on the DVO port from VBT Block 2. In hardware,
Port A is mapped with Pipe A and Port C is mapped with Pipe B.
This issue got introduced in -
commit 7e9804fdcf
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Jan 16 14:27:23 2015 +0200
drm/i915/dsi: add drm mipi dsi host support
Cc: stable@vger.kernel.org # v4.0
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.
Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix a wrong logical AND (&&) used for the range check of CSR MMIO.
Spotted nicely by gcc -Wlogical-op flag:
drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’:
drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op]
Fixes: eb805623d8 ('drm/i915/skl: Add support to load SKL CSR firmware.')
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
connector->encoder is initialized as NULL. Fix this by setting it in
during pre enable. MST connectors are not read out during initial hw
readout, and have no fixed encoder mappings. So it's harmless to
return false when the connector has never been assigned to an encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A few more fixes for amdgpu from the last few days:
- Fix several copy paste typos
- Resume from suspend fixes for VCE
- Fix the GPU scheduler warning in kfifo_out
- Re-enable GPUVM fault interrupts which were inadvertently disabled
- GPUVM page table hang fix when paging
* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
Christian König
Chunming Zhou
Anatoli Antonovitch
Dave Airlie
Ben Skeggs
Roy Spliet
Ilia Mirkin
Jonathon Jongsma
Gaurav K Singh
Ville Syrjälä
Takashi Iwai
Chris Wilson
Maarten Lankhorst
Dave Airlie
Alex Deucher