Handle failure in lwtunnel_fill_encap adding attributes to skb.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_path does not call fib_select_multipath if oif is set in the
flow struct. For VRF use cases oif is always set, so multipath route
selection is bypassed. Use the FLOWI_FLAG_SKIP_NH_OIF to skip the oif
check similar to what is done in fib_table_lookup.
Add saddr and proto to the flow struct for the fib lookup done by the
VRF driver to better match hash computation for a flow.
Fixes: 613d09b30f ("net: Use VRF device index for lookups on TX")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The FIB notification chain is going to be converted to an atomic chain,
which means switchdev drivers will have to offload FIB entries in
deferred work, as hardware operations entail sleeping.
However, while the work is queued fib info might be freed, so a
reference must be taken. To release the reference (and potentially free
the fib info) fib_info_put() will be called, which in turn calls
free_fib_info().
Export free_fib_info() so that modules will be able to invoke
fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting an IP address from an interface, there is a clean-up of
routes which refer to this local address. However, there was no check to
see that the VRF matched. This meant that deletion wasn't confined to
the VRF it should have been.
To solve this, a new field has been added to fib_info to hold a table
id. When removing fib entries corresponding to a local ip address, this
table id is also used in the comparison.
The table id is populated when the fib_info is created. This was already
done in some places, but not in ip_rt_ioctl(). This has now been fixed.
Fixes: 021dd3b8a1 ("net: Add routes to the table associated with the device")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes following sparse errors :
net/ipv4/fib_semantics.c:1579:61: warning: incorrect type in argument 2
(different base types)
net/ipv4/fib_semantics.c:1579:61: expected unsigned int [unsigned]
[usertype] key
net/ipv4/fib_semantics.c:1579:61: got restricted __be32 const
[usertype] nh_gw
Fixes: a6db4494d2 ("net: ipv4: Consider failed nexthops in multipath routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum is reporting for a crash in fib_dump_info
when nh_dev = NULL and fib_nhs == 1:
Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+
RIP: 0033:[<00000000602b3d18>]
RSP: 0000000062623890 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00
RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000
R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00
R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000
Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18
CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581
Stack:
626238f0 960226a02 00000400 000000fe
62623910 600afca7 62623970 62623a48
62468038 00000018 00000000 00000000
Call Trace:
[<602b3e93>] rtmsg_fib+0xd3/0x190
[<602b6680>] fib_table_insert+0x260/0x500
[<602b0e5d>] inet_rtm_newroute+0x4d/0x60
[<60250def>] rtnetlink_rcv_msg+0x8f/0x270
[<60267079>] netlink_rcv_skb+0xc9/0xe0
[<60250d4b>] rtnetlink_rcv+0x3b/0x50
[<60265400>] netlink_unicast+0x1a0/0x2c0
[<60265e47>] netlink_sendmsg+0x3f7/0x470
[<6021dc9a>] sock_sendmsg+0x3a/0x90
[<6021e0d0>] ___sys_sendmsg+0x300/0x360
[<6021fa64>] __sys_sendmsg+0x54/0xa0
[<6021fac0>] SyS_sendmsg+0x10/0x20
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
$ addr2line -e vmlinux -i 0x602b3d18
include/linux/inetdevice.h:222
net/ipv4/fib_semantics.c:1264
Problem happens when RTNH_F_LINKDOWN is provided from user space
when creating routes that do not use the flag, catched with
netlink fuzzer.
Currently, the kernel allows user space to set both flags
to nh_flags and fib_flags but this is not intentional, the
assumption was that they are not set. Fix this by rejecting
both flags with EINVAL.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Fixes: 0eeb075fad ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Dinesh Dutt <ddutt@cumulusnetworks.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath route lookups should consider knowledge about next hops and not
select a hop that is known to be failed.
Example:
[h2] [h3] 15.0.0.5
| |
3| 3|
[SP1] [SP2]--+
1 2 1 2
| | /-------------+ |
| \ / |
| X |
| / \ |
| / \---------------\ |
1 2 1 2
12.0.0.2 [TOR1] 3-----------------3 [TOR2] 12.0.0.3
4 4
\ /
\ /
\ /
-------| |-----/
1 2
[TOR3]
3|
|
[h1] 12.0.0.1
host h1 with IP 12.0.0.1 has 2 paths to host h3 at 15.0.0.5:
root@h1:~# ip ro ls
...
12.0.0.0/24 dev swp1 proto kernel scope link src 12.0.0.1
15.0.0.0/16
nexthop via 12.0.0.2 dev swp1 weight 1
nexthop via 12.0.0.3 dev swp1 weight 1
...
If the link between tor3 and tor1 is down and the link between tor1
and tor2 then tor1 is effectively cut-off from h1. Yet the route lookups
in h1 are alternating between the 2 routes: ping 15.0.0.5 gets one and
ssh 15.0.0.5 gets the other. Connections that attempt to use the
12.0.0.2 nexthop fail since that neighbor is not reachable:
root@h1:~# ip neigh show
...
12.0.0.3 dev swp1 lladdr 00:02:00:00:00:1b REACHABLE
12.0.0.2 dev swp1 FAILED
...
The failed path can be avoided by considering known neighbor information
when selecting next hops. If the neighbor lookup fails we have no
knowledge about the nexthop, so give it a shot. If there is an entry
then only select the nexthop if the state is sane. This is similar to
what fib_detect_death does.
To maintain backward compatibility use of the neighbor information is
based on a new sysctl, fib_multipath_use_neigh.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug report (https://bugzilla.kernel.org/show_bug.cgi?id=107071) noted
that the follwoing ip command is failing with v4.3:
$ ip route add 10.248.5.0/24 dev bond0.250 table vlan_250 src 10.248.5.154
RTNETLINK answers: Invalid argument
021dd3b8a1 changed the lookup of the given preferred source address to
use the table id passed in, but this assumes the local entries are in the
given table which is not necessarily true for non-VRF use cases. When
validating the preferred source fallback to the local table on failure.
Fixes: 021dd3b8a1 ("net: Add routes to the table associated with the device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes how the multipath hash is computed for locally
generated flows: now the hash comprises l4 information.
This allows better utilization of the available paths when the existing
flows have the same source IP and the same destination IP: with l3 hash,
even when multiple connections are in place simultaneously, a single path
will be used, while with l4 hash we can use all the available paths.
v2 changes:
- use get_hash_from_flowi4() instead of implementing just another l4 hash
function
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nexthop is part of multipath route we should clear the
LINKDOWN flag when link goes UP or when first address is added.
This is needed because we always set LINKDOWN flag when DEAD flag
was set but now on UP the nexthop is not dead anymore. Examples when
LINKDOWN bit can be forgotten when no NETDEV_CHANGE is delivered:
- link goes down (LINKDOWN is set), then link goes UP and device
shows carrier OK but LINKDOWN remains set
- last address is deleted (LINKDOWN is set), then address is
added and device shows carrier OK but LINKDOWN remains set
Steps to reproduce:
modprobe dummy
ifconfig dummy0 192.168.168.1 up
here add a multipath route where one nexthop is for dummy0:
ip route add 1.2.3.4 nexthop dummy0 nexthop SOME_OTHER_DEVICE
ifconfig dummy0 down
ifconfig dummy0 up
now ip route shows nexthop that is not dead. Now set the sysctl var:
echo 1 > /proc/sys/net/ipv4/conf/dummy0/ignore_routes_with_linkdown
now ip route will show a dead nexthop because the forgotten
RTNH_F_LINKDOWN is propagated as RTNH_F_DEAD.
Fixes: 8a3d03166f ("net: track link-status of ipv4 nexthops")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fib_netdev_event calls fib_disable_ip on NETDEV_DOWN event
we should not delete the local routes if the local address
is still present. The confusion comes from the fact that both
fib_netdev_event and fib_inetaddr_event use the NETDEV_DOWN
constant. Fix it by returning back the variable 'force'.
Steps to reproduce:
modprobe dummy
ifconfig dummy0 192.168.168.1 up
ifconfig dummy0 down
ip route list table local | grep dummy | grep host
local 192.168.168.1 dev dummy0 proto kernel scope host src 192.168.168.1
Fixes: 8a3d03166f ("net: track link-status of ipv4 nexthops")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes
net/built-in.o: In function `fib_rebalance':
fib_semantics.c:(.text+0x9df14): undefined reference to `__divdi3'
and
net/built-in.o: In function `fib_rebalance':
net/ipv4/fib_semantics.c:572: undefined reference to `__aeabi_ldivmod'
Fixes: 0e884c78ee ("ipv4: L3 hash-based multipath")
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaces the per-packet multipath with a hash-based multipath using
source and destination address.
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of VRF patches used 'int' for table id. It should be u32 to be
consistent with the rest of the stack.
Fixes:
4e3c89920c ("net: Introduce VRF related flags and helpers")
15be405eb2 ("net: Add inet_addr lookup by table")
30bbaa1950 ("net: Fix up inet_addr_type checks")
021dd3b8a1 ("net: Add routes to the table associated with the device")
dc028da54e ("inet: Move VRF table lookup to inlined function")
f6d3c19274 ("net: FIB tracepoints")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the following case doesn't use DCTCP, even if it should:
A responder has f.e. Cubic as system wide default, but for a specific
route to the initiating host, DCTCP is being set in RTAX_CC_ALGO. The
initiating host then uses DCTCP as congestion control, but since the
initiator sets ECT(0), tcp_ecn_create_request() doesn't set ecn_ok,
and we have to fall back to Reno after 3WHS completes.
We were thinking on how to solve this in a minimal, non-intrusive
way without bloating tcp_ecn_create_request() needlessly: lets cache
the CA ecn option flag in RTAX_FEATURES. In other words, when ECT(0)
is set on the SYN packet, set ecn_ok=1 iff route RTAX_FEATURES
contains the unexposed (internal-only) DST_FEATURE_ECN_CA. This allows
to only do a single metric feature lookup inside tcp_ecn_create_request().
Joint work with Florian Westphal.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Feature bits that are invalid should not be accepted by the kernel,
only the lower 4 bits may be configured, but not the remaining ones.
Even from these 4, 2 of them are unused.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_create_info() is already quite large, so before adding more
code to the metrics section move that to a helper, similar to
ip6_convert_metrics.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cfg and family arguments to lwt build state functions. cfg is a void
pointer and will either be a pointer to a fib_config or fib6_config
structure. The family parameter indicates which one (either AF_INET
or AF_INET6).
LWT encpasulation implementation may use the fib configuration to build
the LWT state.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern
Linus Torvalds
Ido Schimmel
David S. Miller
Mark Tomlinson
Eric Dumazet
Julian Anastasov
Paolo Abeni
Peter Nørlund
Daniel Borkmann
Florian Westphal
Tom Herbert