Some drivers are retrieving the nand_chip pointer using the container_of
macro on a struct wrapping both the nand_chip and the mtd_info struct while
the standard way of retrieving this pointer is through mtd->priv.
Provide an helper to do that.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->init_size() hook was introduced to let NAND controller drivers
support NAND devices that could not be described in the nand_ids table.
Since then, the core has added support for extended-id parsing and
full-id description, thus allowing to describe pretty much all existing
NANDs.
Moreover, this hook is not used by any mainline driver, and should not be
used by new drivers, because detecting the NAND chip is not something
controller specific.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use a more descriptive name for the device_node element in struct nand_chip .
This name matches the element name used for device_node property of a flash
in the spi-nor framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 66507c7bc8 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer") added a flag NAND_USE_BOUNCE_BUFFER
using the same bit value as the existing NAND_BUSWIDTH_AUTO.
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Fixes: 66507c7bc8 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
read_page_raw and write_page_raw method description is not clear enough.
It clearly specifies that ECC correction should not be involved but does
not talk about specific layout (by layout I mean where in-band and
out-of-band data are stored on the NAND media) used by NAND/ECC
controllers.
Those specific layouts might impact MTD users and thus should be hidden (as
already done in the standard NAND_ECC_HW_SYNDROME implementation).
Clearly state this constraint in the nand_ecc_ctrl struct documentation.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the comment type (from /** to /*) to prevent DocBook from
complaining about missing description for nand_sdr_timings fields.
There is currently no need in documenting those fields because they are
fully described in the ONFI specification (which is pointed out in the
comment).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_base can be passed a kmap()'d buffers from highmem by
filesystems like jffs2. This results in failure to map the
physical address of the DMA buffer on various contoller
driver on different platforms. This change adds a chip option
to use preallocated databuf as bounce buffers used in
nand_do_read_ops() and nand_do_write_ops().
This allows for specific nand controller driver to set this
option as needed.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The nand_chip::erase_cmd callback previously served a dual purpose; for
one, it allowed a per-flash-chip override, so that AG-AND devices could
use a different erase command than other NAND. These AND devices were
dropped in commit 14c6578683 (mtd: nand:
remove AG-AND support). On the other hand, some drivers (denali and
doc-g4) need to use this sort of callback to implement
controller-specific erase operations.
To make the latter operation easier for some drivers (e.g., ST's new BCH
NAND driver), it helps if the command dispatch and wait functions can be
lumped together, rather than called separately.
This patch does two things:
1. Pull the call to chip->waitfunc() into chip->erase_cmd(), and return
the status from this callback
2. Rename erase_cmd() to just erase(), since this callback does a
little more than just send a command
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
GET_FEATURES and SET_FEATURES also need byte-addressing on 16-bit devices.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the "page" argument for the read_subpage hook. With this argument,
the implementation of this hook could prints out more accurate information
for debugging.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the parsing code for the JEDEC compliant NAND.
Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to get the supported features for JEDEC compliant NAND.
Also add a macro JEDEC_FEATURE_16_BIT_BUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the jedec_version field, and add an anonymous union which
contains the nand_onfi_params and nand_jedec_params.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Create the nand_jedec_params{} and jedec_ecc_info{} according to
the JESD230A (Revision of JESD230, October 2012).
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON
Marek Vasut
Scott Wood
Brian Norris
Randy Dunlap
Ezequiel Garcia
Kamal Dasu
David Mosberger
Huang Shijie