The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.
Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.
Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().
This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.
The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge the bus reset code from NCR5380.c into atari_NCR5380.c. This allows
for removal of a lot of duplicated code conditional on the RESET_BOOT
macro (in the next patch).
The atari_NCR5380.c fork lacks the do_reset() and NCR5380_poll_politely()
routines from NCR5380.c, so introduce them. They are indispensible. Keep
the two implementations in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move board-specific code like this,
NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
from the core driver to the board driver. Eliminate the NCR53C400 macro
from the core driver. Removal of all macros like this one will be
necessary in order to have one core driver that can support all kinds of
boards.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch splits the NCR5380_init() function into two parts, similar
to the scheme used with atari_NCR5380.c. This avoids two problems.
Firstly, NCR5380_init() may perform a bus reset, which would cause the
chip to assert IRQ. The chip is unable to mask its bus reset interrupt.
Drivers can't call request_irq() before calling NCR5380_init(), because
initialization must happen before the interrupt handler executes. If
driver initialization causes an interrupt it may be problematic on some
platforms. To avoid that, first move the bus reset code into
NCR5380_maybe_reset_bus().
Secondly, NCR5380_init() contains some board-specific interrupt setup code
for the NCR53C400 that does not belong in the core driver. In moving this
code, better not re-order interrupt initialization and bus reset. Again,
the solution is to move the bus reset code into NCR5380_maybe_reset_bus().
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NCR5380_local_declare and NCR5380_setup macros exist to define and
initialize a particular local variable, to provide the address of the
chip registers needed for the driver's implementation of its
NCR5380_read/write register access macros.
In cumana_1 and macscsi, these macros generate pointless code like this,
struct Scsi_Host *_instance;
_instance = instance;
In pas16, the use of NCR5380_read/write in pas16_hw_detect() requires that
the io_port local variable has been defined and initialized, but the
NCR5380_local_declare and NCR5380_setup macros can't be used for that
purpose because the Scsi_Host struct has not yet been instantiated.
Moreover, these macros were removed from atari_NCR5380.c long ago and
now they constitute yet another discrepancy between the two core driver
forks.
Remove these "optimizations".
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ASM macro is never defined. rtrc in pas16.c is not used.
NCR5380_map_config, do_NCR5380_intr, do_t128_intr and do_pas16_intr
are unused. NCR_NOT_SET harms readability. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace {P,T,DTC}DEBUG_INIT with NDEBUG_INIT. Remove dead debugging
code, including code that's conditional upon *DEBUG_TRANSFER.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This drop enables a future card with a device id of 0x0600 to be
recognized by the cxlflash driver.
As per the design, the Accelerator Function Unit (AFU) for this new IBM
CXL Flash Adapter retains the same host interface as the previous
generation. For the early prototypes of the new card, the driver with
this change behaves exactly as the driver prior to this behaved with the
earlier generation card. Therefore, no card specific programming has
been added. These card specific changes can be staged in later if
needed.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an async error interrupt is generated, and the error requires the FC
link to be reset, it cannot be performed in the interrupt context. So a
work element is scheduled to complete the link reset in a process
context. If either an EEH event or an escalation occurs in between when
the interrupt is generated and the scheduled work is started, the MMIO
space may no longer be available. This will cause an oops in the worker
thread.
[ 606.806583] NIP kthread_data+0x28/0x40
[ 606.806633] LR wq_worker_sleeping+0x30/0x100
[ 606.806694] Call Trace:
[ 606.806721] 0x50 (unreliable)
[ 606.806796] wq_worker_sleeping+0x30/0x100
[ 606.806884] __schedule+0x69c/0x8a0
[ 606.806959] schedule+0x44/0xc0
[ 606.807034] do_exit+0x770/0xb90
[ 606.807109] die+0x300/0x460
[ 606.807185] bad_page_fault+0xd8/0x150
[ 606.807259] handle_page_fault+0x2c/0x30
[ 606.807338] wait_port_offline.constprop.12+0x60/0x130 [cxlflash]
To prevent the problem space area from being unmapped, when there is
pending work, a mapcount (using the kref mechanism) is held. The
mapcount is released only when the work is completed. The last
reference release is tied to the unmapping service.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a few iterations of resetting the card, either during EEH
recovery, or a host_reset the following is seen in the logs. cxlflash
0008:00: cxlflash_queuecommand: could not get a free command
At every reset of the card, the commands that are outstanding are being
leaked. No effort is being made to reap these commands. A few more
resets later, the above error message floods the logs and the card is
rendered totally unusable as no free commands are available.
Iterated through the 'cmd' queue and printed out the 'free' counter and
found that on each reset certain commands were in-use and stayed in-use
through subsequent resets.
To resolve this issue, when the card is reset, reap all the commands
that are active/outstanding.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Applications which use virtual LUN's that are backed by a physical LUN
over both adapter ports may experience an I/O failure in the event of a
link loss (e.g. cable pull).
Virtual LUNs may be accessed through one or both ports of the adapter.
This access is encoded in the translation entries that comprise the
virtual LUN and used by the AFU for load-balancing I/O and handling
failover scenarios. In a link loss scenario, even though the AFU is able
to maintain connectivity to the LUN, it is up to the application to
retry the failed I/O. When applications are unaware of the virtual LUN's
underlying topology, they are unable to make a sound decision of when to
retry an I/O and therefore are forced to make their reaction to a failed
I/O absolute. The result is either a failure to retry I/O or increased
latency for scenarios where a retry is pointless.
To remedy this scenario, provide feedback back to the application on
virtual LUN creation as to which ports the LUN may be accessed. LUN's
spanning both ports are candidates for a retry in a presence of an I/O
failure.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The original fix to escalate a 'login timed out' error to a LINK_RESET
was only made for one of the two ports on the card. This fix resolves
the same issue for the second port (port 1).
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On the interrupt path, we repeatedly establish the pointer to the
storvsc_device. While the compiler does inline get_in_stor_device() (and
other static functions) in the call chain in the interrupt path, the
compiler is repeatedly inlining the call to get_in_stor_device() each
time it is invoked. The return value of get_in_stor_device() can be
cached in the interrupt path since there is higher level serialization
in place to ensure correct handling when the module unload races with
the processing of an incoming message from the host. Optimize this code
path by caching the pointer to storvsc_device and passing it as an
argument.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function storvsc_channel_init() repeatedly interacts with the host
to extract various channel properties. Refactor this code to eliminate
code repetition.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For FC devices managed by this driver, atttach the appropriate transport
template. This will allow us to create the appropriate sysfs files for
these devices. With this we can publish the wwn for both the port and the node.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain
Manoj Kumar
Uma Krishnan
Matthew R. Ochs
K. Y. Srinivasan
Wilfried Weissmann
Tomas Henzl
Don Brace