a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication. Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nearly every invocation of memset in drivers/staging/hv/StorVsc.c has
its arguments the wrong way around.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers allow O_NDELAY of a dead port (eg for setserial to work). In that
situation we must not try to raise the carrier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: gcm - fix another complete call in complete fuction
crypto: padlock-aes - Use the correct mask when checking whether copying is required
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix sparse warning
[CIFS] Duplicate data on appending to some Samba servers
[CIFS] fix oops in cifs_lookup during net boot
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
at24: Use timeout also for read
i2c: Fix userspace_device list corruption
MAINTAINERS: Add missing i2c files
i2c/tsl2550: Fix lux value in extended mode
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Update mach-types
ARM: 5793/1: ARM: Check put_user fail in do_signal when enable OABI_COMPAT
MAINTAINERS: add maintainer information for AMBA primecell drivers
[ARM] pxa/spitz: fix compile regression on spitz
ARM: PNX4008: i2c-pnx: use the same dev_id for request_irq and free_irq
[ARM] pxa/cpufreq: fix index assignments for end marker
ARM: PNX4008: fix watchdog device driver name
[ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Oliver Neukum
Daniel Glöckner
Ajay Kumar Gupta
Thomas Dahlmann
Eric W. Biederman
Sergei Shtylyov
Alan Stern
Bartlomiej Zolnierkiewicz
Haiyang Zhang
Dave Jones
Michal Simek
Maxime Bizon
Alan Cox
Linus Torvalds
Becky Bruce