The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't currently update the DPMS status of the connector (both in the
connector itself and the connector's DPMS property) in the fb helper
code. This means that if the kernel FB core has blanked the screen,
sysfs will still show a DPMS status of "on". It also means that when X
starts, it will try to light up the connectors, but the drm_crtc_helper
code will ignore the DPMS change since according to the connector, the
DPMS status is already on.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28436 (the annoying
"my screen was blanked when I started X and now it won't light up" bug).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Repeated ttm_page_alloc_init/fini fails noisily because the pool
manager kobj isn't zeroed out between uses (we could do just that but
statically allocated kobjects are generally considered a bad thing).
Move it to kzalloc'ed memory.
Note that this patch drops the refcounting behavior of the pool
allocator init/fini functions: it would have led to a race condition
in its current form, and anyway it was never exploited.
This fixes a regression with reloading kms modules at runtime, since
page allocator was introduced.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
The eDP spec claims a 20% overhead for the 8:10 encoding scheme used
on the wire. Take this into account when picking the lane/clock speed
for the panel.
v3: some panels are out of spec, try our best to deal with them, don't
refuse modes on eDP panels, and try the largest allowed settings if
all else fails on eDP.
v4: fix stupid typo, forgot to git add before amending.
Fixes several reports in bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=28070
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we fill the tail of the physical ring buffer with NOOP when wrapping,
we need to account for the reduction in available space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.
reported by DHR in irc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled. However, the code as is has some
other issues potentially leading to visible problems.
First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer. Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward. So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution. Also, it should be prevented from rearming itself in that
case.
Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..
Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).
Fix the issues described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table. Check both and make sure
we have a value system memory clock value.
v2: make sure rs690_pm_info is called on rs780/rs880 as well.
fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: Dave Airlie <airlied@redhat.com>
HDP non surface should cover the whole VRAM but we were misscomputing
the size and we endup in some case not covering the VRAM at all (if
VRAM size were > 1G). Covering more than the VRAM size shouldn't be
an issue.
Fix : https://bugs.freedesktop.org/show_bug.cgi?id=28016
[airlied: add evergreen fix]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher
Jesse Barnes
Francisco Jerez
Linus Torvalds
Jesse Barnes
Prarit Bhargava
Dan Carpenter
Andy Lutomirski
Dave Airlie
Chris Wilson
Rafael J. Wysocki
Jerome Glisse