The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All Elantech touchpads pre-v4 with dynamic resolution queries have a fixed
resolution of 800dpi -> 31.49 units/mm. Set this statically, so userspace
does not have to guess.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The firmware only reports hover condition while the very first contact is
approaching the surface; the hover is not reported for the subsequent
contacts. Therefore we should not be using ABS_MT_DISTANCE to report hover
but rather its single-touch counterpart ABS_DISTANCE.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix this compile error:
drivers/built-in.o: In function `arc_ps2_probe':
/mnt/linux/drivers/input/serio/arc_ps2.c:206: undefined reference to `devm_ioremap_resource'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning:
drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
size, fw->size);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of iterating over all bits in a bitmap and test them individually
let's siwtch to for_each_set_bit() which is more compact and is also
faster.
Also use bitmap_weight() when counting number of set bits.
This also fixes INPUT_DO_TOGGLE() implementation as it should have used
*_CNT as the upper boundary, not *_MAX.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we are reporting the button state as inverted on all boards with
an axp209 pmic, tested on a ba10-tvbox, bananapi, bananapro, cubietruck and
utoo-p66 tablet.
The axp209 datasheet clearly states that the power button must be connected
between the PWRON key and ground. Which means that on a press we will get
a falling edge (dbf) irq not a rising one, and likewise on release we will
get a rising edge (dbr) irq, not a falling one.
This commit swaps the check for the 2 irqs fixing the inverted reporting of
the power button state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers. Command
sequence found by sniffing the Windows data stream when plugging the
device in.
Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e21 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
Cc: stable@vger.kernel.org
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bastien Nocera
Dmitry Torokhov
Bernhard Bender
Peter Hutterer
Oleksij Rempel
duson
HungNien Chen
Sebastian Ott
Anshul Garg
Hans de Goede
Pavel Rojtberg
Pierre-Loup A. Griffais
Fabio Estevam
Frodo Lai
Uwe Kleine-König
Samuel Thibault
Fabian Frederick