Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot. Delayed stripes are now further
delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when:
* a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
* 'handle_list' is empty and i/o is being done to satisfy full stripe-width
write requests
* 'bypass_count' is less than 'bypass_threshold'. By default the threshold
is 1, i.e. every other stripe handled is a preread stripe provided the
top two conditions are false.
Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
* patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)
Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
* patched: +13%
* patched + preread_bypass_threshold = 0: +37%
Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
make it configurable. This defaults to fairness and modest performance
gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
necessary, the important change was clearing STRIPE_DELAYED in
add_stripe_bio and this has been moved out to make_request for the hang
fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
of stripes being naturally promoted off of hold_list +2%. Note, resetting
bypass_count instead of decrementing on these events yields +4% but that is
probably too aggressive.
Changes since v3:
* cosmetic fixups
Tested-by: James W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/md/md.c:734:16: warning: Using plain integer as NULL pointer
drivers/md/md.c:1115:16: warning: Using plain integer as NULL pointer
Add some braces to match the else-block as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the 965G and 965GM graphic chipsets to the intelfb driver. I
have a notebook with an Intel Mobile GM965/GL960 Integrated Graphics
Controller and with the attached patch the framebuffer comes up. I have
tested it a bit with DirectFB to make sure it is working stable.
I also have an Intel Mobile GM945 and I compared the results, the programming
interface of the 9xx series from Intel is mostly the same, so I think the
patch should add all the functionality which the 945GM has.
Signed-off-by: Maik Broemme <mbroemme@plusserver.de>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note: looks like accesses to "registered_fb" are done without any exclusion
so there're none in new proc code, too. This should be fixed in separate
patch.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a bugfix for the use of cfb_* functions instead of sys_*
functions. sys_* should be used with vmalloced framebuffers. the previous
cfb_ use would not work for callers of imageblit/etc.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since there's no way to autodetect panel modes, we're forced to hardcode them
in the driver and add a big fat #ifdef. The OLPC DCON needs a specific mode
line (at 1200x900). This adds it to both gxfb and lxfb.
(Jordan said: We could probably detect the panel mode, but there isn't any
reason to since the panel timings are well known and won't change. While OFW
detection would be good computer science fu, it would be a wasted effort since
its so easy to hard code them into the table.)
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there's no VSA2 (ie, if we're using tinybios or OpenFirmware), use the
GLIU's P2D Range Offset Descriptor to determine how much memory we have
available for the framebuffer.
Originally based on a patch by Jordan Crouse. Tested with OpenFirmware;
Pascal informs me that tinybios has a stub that fills in P2D_RO0.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams
Harvey Harrison
Mike Frysinger
Andrew Morton
Maik Broemme
Alexey Dobriyan
Jaya Kumar
Sebastian Siewior
York Sun
Andres Salomon