The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
get_user() may fail, if so return -EFAULT.
[Fixed one missing place by tiwai]
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that if (dev == SNDRV_CARDS) we're one past the end of
the array. That's unlikely to happen in real life, I suppose.
Also smatch complains about "strcpy(card->shortname, pcm->name);"
The "pcm->name" buffer is 80 characters and "card->shortname" is 32
characters. If you follow the call paths it turns out we never actually
use more than 16 characters so it's not a problem. But anyway, let's
make it easy for people auditing this in the future.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the snd_es1688 during the snd_card allocation.
This allows to remove the card pointer from the snd_es1688 structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is only one dma for the ESS ES968 based board.
Its index is 0 and not 1.
This make the es968 card working.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The llseek implementation is identical for existing driver implementations,
so let's merge to the common layer. The same code for the text proc file
can be used even for the binary proc file.
The driver can provide its own llseek method if needed. Then the common
code will be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the validity of the file position in the common info layer before
calling read or write callbacks in assumption that entry->size is set up
properly to indicate the max file size.
Removed the redundant checks from the callbacks as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix 'else' placement in ifdef block so that build succeeds:
sound/isa/opti9xx/opti92x-ad1848.c:221: error: 'else' without a previous 'if'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While trying to compile jazz16 isa sound driver on alpha (2.6.33+git), I
found a compile failure in jazz16.c (udelay is unknown). Fix it by
including delay.h.
Signed-foo-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Master Control port (MC) is available as the last
PnP resource (OPT005). Use this value instead fo guessing.
Also, add some comments to the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Narrow the dma and irq selection after the DOS driver.
Add ALSA configuration description as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lucas De Marchi
Uwe Kleine-König
Takashi Iwai
Joe Perches
René Herman
Kulikov Vasiliy
Dan Carpenter
Krzysztof Helt
Tejun Heo
Randy Dunlap
Meelis Roos
Jaroslav Kysela