_SDD (Set Device Data) is an ACPI method that is used to tell the
firmware what the identify data is of the device that is attached to
the port. It is an optional method, and it's ok for it to be missing.
Because of this, we always return success from the routine that calls
this method, even if the execution fails.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(cherry picked from 39aa79e0a1f5f2e28aa341f035940746a98b45b1 commit)
_GTF is an acpi method that is used to reinitialize the drive. It returns
a task file containing ata commands that are sent back to the drive to restore
it to boot up defaults.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(cherry picked from 9c69cab24b51a89664f4c0dfaf8a436d32117624 commit)
Some devices chock if Feature is not clear when IDENTIFY is issued.
Set ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE for IDENTIFY such that whole
TF is cleared when reading ID data.
Kudos to Art Haas for testing various futile patches over several
months and Mark Lord for pointing out the fix.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If we are doing a PIO setup for a CFA card and it blows up with a device
error then assume it is an older CFA card which doesn't support this
rather than failing the device out of existance.
Stands seperate to the quieting patch but that is obviously useful with
this change.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Follow the old SRST rule and delay 150ms between completion of
hardreset and status checking. Debouncing delay should usually cover
this but debounce duration could be shorter than 150ms under certain
circumstances.
Usefulness depends on host controller implementation but it can't hurt
and serves as a reminder that 2s delay for GoVault should also be
added here.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Per Jeff's suggestion, this patch rearranges the info printed for ATA
drives into dmesg to add the full ATA firmware revision and model
information, while keeping the output to 2 lines.
Signed-off-by: Eric D. Mudama <edmudama@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is against the libata core and headers.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that all LLDs are converted to use devres, default stop callbacks
are unused. Remove them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update libata core layer to use devres.
* ata_device_add() acquires all resources in managed mode.
* ata_host is allocated as devres associated with ata_host_release.
* Port attached status is handled as devres associated with
ata_host_attach_release().
* Initialization failure and host removal is handedl by releasing
devres group.
* Except for ata_scsi_release() removal, LLD interface remains the
same. Some functions use hacky is_managed test to support both
managed and unmanaged devices. These will go away once all LLDs are
updated to use devres.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_host_detach() which calls ata_port_detach() for each
port in the host and export it. ata_port_detach() is now internal and
thus un-exported. ata_host_detach() will be used as the 'deregister
from libata layer' function after devres conversion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used two separate sets of variables to record request size and
current offset for ATA and ATAPI. This is confusing and fragile.
This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and
kills them. Also, ata_pio_sector() is updated to use bytes for
qc->cursg_ofs instead of sectors. The field used to be used in bytes
for ATAPI and in sectors for ATA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle pci_enable_device() failure while resuming. This patch kills
the "ignoring return value of 'pci_enable_device'" warning message and
propagates __must_check through ata_pci_device_do_resume().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There were several places where ATA ID strings are manually terminated
and in some places possibly unterminated strings were passed to string
functions which don't limit length like strstr(). This patch converts
all of them over to ata_id_c_string().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency
with other ATA_ID_* constants.
* Kill ATA_SERNO_LEN
* Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN.
This change also makes ata_device_blacklisted() use proper length
for fwrev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the following needlessly global functions static:
- libata-core.c: ata_qc_complete_internal()
- libata-scsi.c: ata_scsi_qc_new()
- libata-scsi.c: ata_dump_status()
- libata-scsi.c: ata_to_sense_error()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If word 53 bit 1 isn't set, the maximum PIO mode is indicated by
the upper 8 bits of word 51, not the lower 8 bits. Fixes PIO mode
detection on old Compact Flash cards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Calling sg_init_one() with NULL buf causes oops on certain
configurations. Don't initialize sg in ata_exec_internal() if
DMA_NONE and make the function complain if @buf is NULL when dma_dir
isn't DMA_NONE. While at it, fix comment.
The problem is discovered and initial patch was submitted by Arnd
Bergmann.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata timing computation code makes some mistakes in PIO5/6 because a
check was not updated correctly when I put this support into the kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kristen Carlson Accardi
Tejun Heo
Jeff Garzik
Alan
Eric D. Mudama
Akira Iguchi
Adrian Bunk
Brian King
Lennert Buytenhek