Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65218 LS3 current regulator, which is capable of 4
current input limit modes: 100, 200, 500, and 1000 uA.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many voltage Regulators need a input voltage that is higher than the
output voltage. Allow to specify a minimum dropout voltage which will
be used later to find the best input voltage for regulators.
[Changed uv to uV for consistency and legibility -- broonie]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can automatically shut down when they detect an
over current event. Add an op (set_over_current_protection) and a
DT property + constraint to support this capability.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The docbook for these members is missing. Add them.
Warning(include/linux/regulator/machine.h:147): No description
found for parameter 'soft_start'
Warning(include/linux/regulator/driver.h:197): No description
found for parameter 'set_soft_start'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose the requested load directly to the regulator implementation for
hardware that does not support the normal enum based set_mode().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When drivers use simplified DT parsing method (they provide
'regulator_desc.of_match') they still may want to parse custom
properties for some of the regulators. For example some of the
regulators support GPIO enable control.
Add a driver-supplied callback for such case. This way the regulator
core parses common bindings offloading a lot of code from drivers and
still custom properties may be used.
The callback, called for each parsed regulator, may modify the
'regulator_config' initially passed to regulator_register().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "regulator-initial-mode" and "regulator-mode" DT properties allows
to configure the regulator operating modes at startup or when a system
enters into a susend state.
But these properties use as valid values the operating modes supported
by each device while the core deals with the standard operating modes.
So a mapping function is needed to translate from the hardware specific
modes to the standard ones.
This mapping is a non-varying configuration for each regulator, so add
a function pointer to struct regulator_desc that will allow drivers to
define their callback to do the modes translation.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most drivers do not set the ena_gpio field of struct regulator_config
before passing it to the regulator core. This is fine as long as the
gpio identifier that is passed is a positive integer. But the gpio
identifier 0 is also valid. So we are not able to decide wether we got a
real gpio identifier or not based on a 0 in ena_gpio.
To be able to decide if it is a valid gpio that got passed, this patch
adds a ena_gpio_initialized field that should be set if was initialized
with a correct value, either a gpio >= 0 or a negative error number. The
core then checks if ena_gpio or ena_gpio_initialized before handling it
as a gpio. This way we maintain backwards compatibility and fix the
behaviour for gpio number 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix kernel-doc warnings in regulator header files:
Warning(..//include/linux/regulator/machine.h:140): No description found for parameter 'ramp_disable'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'linear_ranges'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'n_linear_ranges'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build warning:
CC [M] drivers/regulator/hi6421-regulator.o
drivers/regulator/hi6421-regulator.c:356:2: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This is a revert of commit 716845ebeb ("regulator: core: Fix build error due
to const qualifier for ops"). The build error was fixed by commit 39f5460d7f
("regulator: core: add const to regulator_ops and fix build error in mc13892").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop const qualifier for ops of struct regulator_desc.
Allow regulator drivers to update ops before registering regulator.
Fix below build error:
CC [M] drivers/regulator/mc13892-regulator.o
drivers/regulator/mc13892-regulator.c: In function 'mc13892_regulator_probe':
drivers/regulator/mc13892-regulator.c:586:3: error: assignment of member 'set_mode' in read-only object
drivers/regulator/mc13892-regulator.c:588:3: error: assignment of member 'get_mode' in read-only object
make[2]: *** [drivers/regulator/mc13892-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Laxman Dewangan
Nikita Kiryanov
Sascha Hauer
Stephen Boyd
Mark Brown
Bjorn Andersson
Axel Lin
Krzysztof Kozlowski
Javier Martinez Canillas
Markus Pargmann
Randy Dunlap