This adds a typedef for the IRQ bitmap, which should cause
no functional change, but will make it easier to pass a
pointer to a bitmap to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Nothing outside the PNP subsystem should need access to a
device's resource options, so this patch moves the option
structure declarations to a private header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED
in a private header file, but put those flags in struct resource.flags
fields. Better to make them IORESOURCE_IO_* flags like the existing
IRQ, DMA, and MEM flags.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rather than stepping through all IO resources, then stepping through
all MMIO resources, etc., we can just iterate over the resource list
once directly.
This can change the order in /sys, e.g.,
# cat /sys/devices/pnp0/00:07/resources # OLD
state = active
io 0x3f8-0x3ff
irq 4
# cat /sys/devices/pnp0/00:07/resources # NEW
state = active
irq 4
io 0x3f8-0x3ff
The old code artificially sorted resources by type; the new code
just lists them in the order we read them from the ISAPNP hardware
or the BIOS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
We used to have a fixed-size resource table. If a device had
twenty resources when the table only had space for ten, we didn't
need ten warnings, so we added the ratelimit.
Now that we can dynamically allocate new resources, we should
only get failures if the allocation fails. That should be
rare enough that we don't need to ratelimit the messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
When we parse a device's _CRS data (the current resource settings),
we should keep track of everything we find, even if it's currently
disabled or invalid.
This is what we already do for ISAPNP and PNPBIOS, and it helps
keep things matched up when we subsequently re-encode resources.
For example, consider a device with (mem, irq0, irq1, io), where
irq0 is disabled. If we drop irq0 when parsing the _CRS, we will
mistakenly put irq1 in the irq0 slot when we encode resources
for an _SRS call.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device. This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.
This patch replaces the table with a linked list of resources where
the entries are allocated on demand.
This removes messages like these:
pnpacpi: exceeded the max number of IO resources
00:01: too many I/O port resources
References:
http://bugzilla.kernel.org/show_bug.cgi?id=9535http://bugzilla.kernel.org/show_bug.cgi?id=9740http://lkml.org/lkml/2007/11/30/110
This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.
Prior to this patch, the pnp_resource_table entries used the flags
like this:
IORESOURCE_UNSET
This table entry is unused and available for use. When this flag
is set, we shouldn't look at anything else in the resource structure.
This flag is set when a resource table entry is initialized.
IORESOURCE_AUTO
This resource was assigned automatically by pnp_assign_{io,mem,etc}().
This flag is set when a resource table entry is initialized and
cleared whenever we discover a resource setting by reading an ISAPNP
config register, parsing a PNPBIOS resource data stream, parsing an
ACPI _CRS list, or interpreting a sysfs "set" command.
Resources marked IORESOURCE_AUTO are reinitialized and marked as
IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:
- before we attempt to assign resources automatically,
- if we fail to assign resources automatically,
- after disabling a device
IORESOURCE_DISABLED
Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
Also set by PNPBIOS and PNPACPI for:
- invalid IRQs or GSI registration failures
- invalid DMA channels
- I/O ports above 0x10000
- mem ranges with negative length
After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:
IORESOURCE_UNSET
This flag is no longer used in PNP. Instead of keeping
IORESOURCE_UNSET entries in the resource list, we remove
entries from the list and free them.
IORESOURCE_AUTO
No change in meaning: it still means the resource was assigned
automatically by pnp_assign_{port,mem,etc}(), but these functions
now set the bit explicitly.
We still "clean" a device's resource list in the same places,
but rather than reinitializing IORESOURCE_AUTO entries, we
just remove them from the list.
Note that IORESOURCE_AUTO entries are always at the end of the
list, so removing them doesn't reorder other list entries.
This is because non-IORESOURCE_AUTO entries are added by the
ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
sysfs "set" command. In each of these cases, we completely free
the resource list first.
IORESOURCE_DISABLED
In addition to the cases where we used to set this flag, ISAPNP now
adds an IORESOURCE_DISABLED resource when it reads a configuration
register with a "disabled" value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This patch adds a "pnp_resource_type_name(struct resource *)" that
returns the string resource type. This will be used by the sysfs
"show resources" function and the debug resource dump function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
We used pnp_resource.index to keep track of which ISAPNP configuration
register a resource should be written to. We needed this only to
handle the case where a register is disabled but a subsequent register
in the same set is enabled.
Rather than explicitly maintaining the pnp_resource.index, this patch
adds a resource every time we read an ISAPNP configuration register
and marks the resource as IORESOURCE_DISABLED when appropriate. This
makes the position in the pnp_resource_table always correspond to the
config register index.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
In the debug resource dump, decode the flags and indicate when
a resource is disabled or has been automatically assigned.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
"idle=halt" limits the idle loop to using
the halt instruction. No MWAIT, no IO accesses,
no C-states deeper than C1.
If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.
This is useful for debugging, especially for some
interrupt storm issues.
All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.
All GPEs that don't have a _Lxx/_Exx method are marked as invalid.
All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ling Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Eliminated unnecessary operands; eliminated use of negative index
in loop. Operands now displayed in correct order, not backwards.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This problem was introduced in 20080514 as a result of the
elimination of the acpi_native_uint type. Code uses a negative
array index, which should be eliminated.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Some BIOSs erroneously reverse the _PRT SourceName and the
SourceIndex. Detect and repair this problem. MS ACPI also allows
and repairs this problem, thus ACPICA must also.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas
Julia Jomantaite
Zhao Yakui
Zhang Rui
Bob Moore