Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of allocating a struct pps_gpio_platform_data in the DT case,
store the necessary information in struct pps_gpio_device_data itself.
This avoids an additional allocation and the ifdef. It also gets rid of
some indirection.
Also use dev_err instead of pr_err in the changed code.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some users have a large AoE target while others like to use many AoE
targets at the same time. In the latter case, there is an opportunity to
greatly improve aggregate throughput by allowing different threads to
complete the I/O associated with each target. For 36 targets, 4 KiB read
throughput roughly doubles, for example, with these changes in place.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes). This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.
This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect. This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Acked-by: Rob Landley <rob@landley.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NBD_CLEAR_QUE ioctl has been deprecated for quite some time (its job
is now done by two other ioctls). We should stop trying to make bogus
assertions in it. Also, user-level code should remove calls to
NBD_CLEAR_QUE, ASAP.
Signed-off-by: Michal Belczyk <belczyk@bsd.krakow.pl>
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change endpoint device name format to use a component tag value instead of
device destination ID.
RapidIO specification defines a component tag to be a unique identifier
for devices in a network. RapidIO switches already use component tag as
part of their device name and also use it for device identification when
processing error management event notifications.
Forming an endpoint's device name using its component tag instead of
destination ID allows to keep sysfs device directories unchanged in case
if a routing process dynamically changes endpoint's destination ID as a
result of route optimization.
This change should not affect any existing users because a valid device
destination ID always should be obtained by reading "destid" attribute and
not by parsing device name.
This patch also removes switchid member from struct rio_switch because it
simply duplicates the component tag and does not have other use than in
device name generation.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update enumeration/discovery method registration mechanism to allow
loading enumeration/discovery methods before all mports are registered.
Existing statically linked RapidIO subsystem expects that all available
RapidIO mport devices are initialized and registered before the
enumeration/discovery method is registered. Switching to loadable mport
device drivers creates situation when mport device driver can be loaded
after enumeration/discovery method is attached (e.g., loadable mport
driver in a system with statically linked RapidIO core and enumerator).
This also will happen in a system with hot-pluggable RapidIO controllers.
To remove the dependency on the initialization/registration order this
patch introduces enumeration/discovery registration mechanism that
supports arbitrary registration order of mports and enumerator/discovery
methods.
The following registration rules are implemented:
- only one enumeration/discovery method can be registered for given mport ID
(including RIO_MPORT_ANY);
- when new enumeration/discovery methods tries to attach to the registered mport
device, method with matching mport ID will replace a default method previously
registered for given mport (if any);
- enumeration/discovery method with target ID=RIO_MPORT_ANY will be attached
only to mports that do not have another enumerator attached to them;
- when new mport device is registered with RapidIO subsystem, registration
routine searches for the enumeration/discovery method with the best matching
mport ID;
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rework probe/remove routines to prevent rionet driver from monopolizing
target RapidIO devices. Fix conflict with modular RapidIO switch drivers.
Using one of RapidIO messaging channels rionet driver provides a service
layer common to all endpoint devices in a system's RapidIO network. These
devices may also require their own specific device driver which will be
blocked from attaching to the target device by rionet (or block rionet if
loaded earlier). To avoid conflict with device-specific drivers, the
rionet driver is reworked to be registered as a subsystem interface on the
RapidIO bus.
The reworked rio_remove_dev() and rionet_exit() routines also include
handling of individual rionet peer device removal which was not supported
before.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rework RapidIO switch drivers to add an option to build them as loadable
kernel modules.
This patch removes RapidIO-specific vmlinux section and converts switch
drivers to be compatible with LDM driver registration method. To simplify
registration of device-specific callback routines this patch introduces
rio_switch_ops data structure. The sw_sysfs() callback is removed from
the list of device-specific operations because under the new structure its
functions can be handled by switch driver's probe() and remove() routines.
If a specific switch device driver is not loaded the RapidIO subsystem
core will use default standard-based operations to configure a switch.
Because the current implementation of RapidIO enumeration/discovery method
relies on availability of device-specific operations for error management,
switch device drivers must be loaded before the RapidIO
enumeration/discovery starts.
This patch also moves several common routines from enumeration/discovery
module into the RapidIO core code to make switch-specific operations
accessible to all components of RapidIO subsystem.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse warnings:
drivers/rapidio/rio-scan.c:1143:5: sparse: symbol 'rio_enum_mport' was not declared. Should it be static?
drivers/rapidio/rio-scan.c:1246:5: sparse: symbol 'rio_disc_mport' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: "Bounine, Alexandre" <Alexandre.Bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tang Chen
Jean-Francois Dagenais
Libo Chen
Libo Chen
Jan Luebbe
Alexandru Gheorghiu
Kees Cook
Ed Cashin
Paul Clements
Michal Belczyk
Raphael S. Carvalho
Alexandre Bounine
Wu Fengguang