Palmas extcon IRQs are nested threaded and wired to the Palmas
interrupt controller. So, this flag is not required for nested
IRQs anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged. However, the
fix in commit ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME
flag") missed a stray flag causing the following crash on resume on
BeagleBoard-X15 platform:
[ 53.670141] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[..]
[ 53.670141] [<c04ae734>] (omap_set_gpio_triggering) from [<c04aeb94>] (omap_gpio_unmask_irq+0xc0/0xc4)
[ 53.670141] [<c04aeb94>] (omap_gpio_unmask_irq) from [<c01a0b88>] (irq_enable+0x30/0x44)
[ 53.670141] [<c01a0b88>] (irq_enable) from [<c019ebd8>] (__enable_irq+0x54/0x78)
[ 53.670141] [<c019ebd8>] (__enable_irq) from [<c01a4e60>] (resume_irqs+0xe8/0x100)
[ 53.670141] [<c01a4e60>] (resume_irqs) from [<c0514840>] (syscore_resume+0x94/0x298)
[ 53.670141] [<c0514840>] (syscore_resume) from [<c01981cc>] (suspend_devices_and_enter+0x790/0x9e4)
[ 53.670141] [<c01981cc>] (suspend_devices_and_enter) from [<c0198a60>] (pm_suspend+0x640/0x75c)
[ 53.670141] [<c0198a60>] (pm_suspend) from [<c0196bec>] (state_store+0x64/0xb8)
[ 53.670141] [<c0196bec>] (state_store) from [<c0307944>] (kernfs_fop_write+0xc0/0x1bc)
[ 53.670141] [<c0307944>] (kernfs_fop_write) from [<c028acb0>] (__vfs_write+0x1c/0xd8)
[ 53.670141] [<c028acb0>] (__vfs_write) from [<c028bba0>] (vfs_write+0x90/0x16c)
[ 53.670141] [<c028bba0>] (vfs_write) from [<c028c8c0>] (SyS_write+0x44/0x9c)
[ 53.670141] [<c028c8c0>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[..]
Fixes: ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME flag")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The info->status[] array has 3 elements. We are using size
MAX77843_MUIC_IRQ_NUM (16) instead of MAX77843_MUIC_STATUS_NUM (3) as
intended.
Fixes: 135d9f7d13 ('extcon: max77843: Clear IRQ bits state before request IRQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[cw00.choi: Modify the patch title]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We should be using the helper functions to lock the DAPM mutex not
accessing it directly. There are no ill effects of this as the moment
but it is best practice, and the implementation could be changed in the
future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the new EXTCON_CHG_USB_SDP connector to support SDP (Standard
Downstream Port) USB charging port. The commit 11eecf910b ("extcon: Modify
the id and name of external connector") add the new EXTCON_CHG_USB_SDP
connector which support the both data transfer and usb charging at the same
time.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch fixes the typo in comment of extcon-gpio.c driver.
- 'interrput' -> 'interrupt'
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to
enable a system with an integrated USB OTG dual-role transceiver to
function as an USB OTG dual-role device. In addition to sensing/controlling
Vbus, the chip also passes thru the ID signal from the USB OTG connector.
On some Renesas boards, this signal is just fed into the SoC thru a GPIO
pin -- there's no real OTG controller, only host and gadget USB controllers
sharing the same USB bus; however, we'd like to allow host or gadget
drivers to be loaded depending on the cable type, hence the need for the
MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs
(however, we aren't currently interested in them), the OFFVBUS# signal is
controlled by the host controllers, there's also the SHDN# signal wired to
a GPIO, it should be driven high for the normal operation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
[cw00.choi: Add the GPIOLIB dependency]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add device bindings to support configuring the jack detection
configurations. Each configuration needs to specify the connection of
the mic det pins, which micbias should be used and the value of the
micd polarity GPIO required to activate that configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds IRQF_ONESHOT if no primary handler is provided for request
threaded irq.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some Arizona devices have the option to use the GPIO5 pin as a second
jack detection pin. This patch adds device bindings to specify to the
driver that it should use this pin. Note that the second jack detection
pin is hard wired in the chip so can only be enabled through the
binding, rather than a pin being specified.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
By default the driver expects the jackdet pin to be pulled low when a
jack is inserted. This patch adds a device binding that allows the user
to specify that the jackdet pin will be pulled high when a jack is
inserted.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is generally used in conjunction with the MICDET clamp to
suppress pops and clicks associated with jack insertion. This patch adds
a binding that allows the user to select the mode of operation for this
switch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch modifies the id and name of external connector with the
additional prefix to clarify both attribute and meaning of external
connector as following:
- EXTCON_CHG_* mean the charger connector.
- EXTCON_JACK_* mean the jack connector.
- EXTCON_DISP_* mean the display port connector.
Following table show the new name of external connector with old name:
--------------------------------------------------
Old extcon name | New extcon name |
--------------------------------------------------
EXTCON_TA | EXTCON_CHG_USB_DCP |
EXTCON_CHARGE_DOWNSTREAM| EXTCON_CHG_USB_CDP |
EXTCON_FAST_CHARGER | EXTCON_CHG_USB_FAST |
EXTCON_SLOW_CHARGER | EXTCON_CHG_USB_SLOW |
--------------------------------------------------
EXTCON_MICROPHONE | EXTCON_JACK_MICROPHONE |
EXTCON_HEADPHONE | EXTCON_JACK_HEADPHONE |
EXTCON_LINE_IN | EXTCON_JACK_LINE_IN |
EXTCON_LINE_OUT | EXTCON_JACK_LINE_OUT |
EXTCON_VIDEO_IN | EXTCON_JACK_VIDEO_IN |
EXTCON_VIDEO_OUT | EXTCON_JACK_VIDEO_OUT |
EXTCON_SPDIF_IN | EXTCON_JACK_SPDIF_IN |
EXTCON_SPDIF_OUT | EXTCON_JACK_SPDIF_OUT |
--------------------------------------------------
EXTCON_HMDI | EXTCON_DISP_HDMI |
EXTCON_MHL | EXTCON_DISP_MHL |
EXTCON_DVI | EXTCON_DISP_DVI |
EXTCON_VGA | EXTCON_DISP_VGA |
--------------------------------------------------
And, when altering the name of USB charger connector, EXTCON refers to the
"Battery Charging v1.2 Spec and Adopters Agreement"[1] to use the standard
name of USB charging port as following. Following name of USB charging port
are already used in power_supply subsystem. We chan check it on patch[2].
- EXTCON_CHG_USB_SDP /* Standard Downstream Port */
- EXTCON_CHG_USB_DCP /* Dedicated Charging Port */
- EXTCON_CHG_USB_CDP /* Charging Downstream Port */
- EXTCON_CHG_USB_ACA /* Accessory Charger Adapter */
[1] www.usb.org/developers/docs/devclass_docs/BCv1.2_070312.zip
[2] commit 85efc8a18c ("power_supply: Add types for USB chargers")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[ckeepax: For the Arizona changes]
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
This patch uses the descriptor-based GPIO interface (gpiod_* API) instead of
legacy gpio_* API and add the internal gpio_extcon_init() to handle
all gpio-related tasks.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch fixes the minor coding style about indentation and removes the
unused fields from struct gpio_extcon_platform_data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The commit 2a9de9c0 ("extcon: Use the unique id for external connector instead
of string") defines the unique id of each external connector to identify the
type of external connector instead of string name. So, devm_extcon_dev_allocate()
should include the second parameter (unsigned int *supported_cable). This patch
adds the supported_cable parameter which is passed by platform data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There are duplicate data between struct gpio_extcon_data and struct
gpio_extcon_platform_data. This patch removes them from struct gpio_extcon_data.
Instead, this patch add pdata field to struct gpio_extcon_data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Nishanth Menon
Grygorii Strashko
Felipe Balbi
Dan Carpenter
Charles Keepax
Chanwoo Choi
Moritz Fischer
Geliang Tang
Sergei Shtylyov
Andrzej Hajda
Saurabh Sengar